Sony IFB-LE100, Руководство по обслуживанию

Страница: 15 / 258

1-9
VPD-LE100A/LE100E/LE100U
16
Location and Function of Controls
0 0
CONTOROL S
IN
PLIG IN POWER
STATUS/ERROR MESSAGE
OUT
STANDBY
1
ON
@
RS-
232C
RS-
422A
RS-232C/422A PJ COM IN
R G/G SYNC SYNC/HD VD B
OUT
TRIG DEVICE INDEX CONTOROL
Rear
Remote
commander
cable (supplied)
Remote Commander
to CONTROL S OUT
to CONTROL
S IN
Be sure to install the battery
from the
# side.
wa
PO/– keys
These keys do not function with this projector.
ws FUNCTION key
The key does not function with this projector.
wd ENTER key
Stores the settings in the menu.
wf Arrow and +/– keys ( M / m / < / , /+/–)
Used to adjust the picture after pressing the LENS
CONTROL or RGB key. Also used to move the cursor
or adjust the value in the menu.
wg MENU key
Displays the menu on the screen.
Press again to turn off the menu.
wh CONTROL S OUT jack
Connect the supplied remote commander cable to this
jack and to the CONTROL S IN jack of the projector
for wired remote control operation.
When the Commander is connected to the CONTROL
S IN/PLUG IN POWER jack of the projector via the
remote commander cable (stereo), the power for the
Remote Commander is supplied from the projector.
Battery installation
1
Push to open the lid, and install three R6 (size AA)
batteries (supplied) with the polarities correctly
aligned.
2
Replace the lid.
Notes on batteries
• Make sure that the battery orientation is correct when
inserting batteries.
• Do not mix old battery with new one, or different
types of batteries.
• If you will not use the Remote Commander for a long
time, remove the batteries to avoid damage from
battery leakage. If batteries have leaked, remove
them, wipe the battery compartment dry and replace
the batteries with new ones.
Notes on wireless Remote Commander
operation
• Be sure that there is nothing to obstruct the infrared
beam between the Remote Commander and the
projector.
• The operation range is limited. The shorter the
distance between the Remote Commander and the
projector, the wider the angle within which the
commander can control the projector.
• The remote control detectors on the projector do not
operate when connecting the remote commander
cable to the CONTROL S IN jack. If you wish to use
the Remote Commander as a wireless Remote
Commander, be sure to remove the remote
commander cable from both the Remote Commander
and the projector.
To connect the Remote Commander to the
projector
Note on wired Remote Commander operation
using the supplied remote commander cable
(stereo)
You do not need to install the batteries since the power
is supplied from the CONTROL S IN jack on the
projector. In this case, the batteries are not consumed.
17
Precautions on Installation
Avoid installing the projector in a location
subject to excessive dust
Do not use the projector while laying it on
its side or upside down
Do not tilt the projector when in use
Avoid tilting the projector more than ±5 degrees or installing it
other than on the floor and ceiling. Such installations may cause
malfunctions such as color irregularity or shortening of lamp life.
Do not cover the ventilation holes
(exhaust)
Do not cover the ventilation holes (exhaust) on the left side;
otherwise, internal heat may build up.
Do not install the projector on a deep-pile
carpet
If you install the projector on a deep-pile carpet, the ventilation
holes (intake) may be blocked, causing an internal heat build-up.
Precautions on Installation
For installation examples with projection distances, see the
supplied “Projection Distance Charts.”
Do not install the projector in the following situations. These
installations may cause malfunction or damage to the projector.
Do not install the projector in an ill-
ventilated place
The projector is equipped with ventilation holes for intake and
these for exhaust on the front, left and right sides to prevent
internal heat build-up. Do not block these ventilation holes and
allow adequate air circulation at an installation location.
Do not place any object beside the
projector
If you put something beside the ventilation holes on the sides, the
exhaust may be inhaled into the projector through the ventilation
holes (intake), causing the internal temperature to rise and thereby
activating the protection circuit. Install the projector so that the
exhaust is not blocked.
Do not install the projector in a location
where temperature or humidity is very
high
Avoid installing the projector in a location
where temperature may rise or fall rapidly
Be careful of air-conditioning and heating in a room where the
projector is installed, as sudden changes in temperature may lead to
moisture condensation and cause damage to the projector.
Setting up and projecting
±5°