HT-S200F/SF200/SF201
HT-S200F/SF200/SF201
33
33
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
For Printed Wiring Boards.
Note:
•
X
: Parts extracted from the component side.
•
Y
: Parts extracted from the conductor side.
•
: Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Caution:
Pattern face side:
(SIDE B)
Parts face side:
(SIDE A)
Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• MAIN board is multi-layer printed board. However, the
patterns of intermediate layers have not been included in
diagrams.
• Indication of transistor.
C
B
These are omitted.
E
Q
For Schematic Diagrams.
Note:
• All capacitors are in
μ
F unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in
Ω
and 1/4 W or less unless otherwise
speci
fi
ed.
•
C
: Panel designation.
•
A
: B+ Line.
• Voltages are dc with respect to ground under no-signal
conditions.
no mark : POWER ON
( ) : IR REPEATER ON
*
: Impossible to measure
• Voltages are taken with VOM (Input impedance 10 M
).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F
:
AUDIO
(ANALOG)
J
:
AUDIO
(DIGITAL)
L
:
USB
d
:
BLUETOOTH
Note 1:
When the complete MAIN board is replaced, refer to
“SPREADING OF COMPOUND” on page 4.
Note 2:
Among mounted electrical parts on each board, only
parts that are described in the electrical parts list can
be replaced for repairing.
The parts that are not described in the electrical parts
list cannot be replaced with single for repairing.
Note 1:
When the complete MAIN board is replaced, refer to
“SPREADING OF COMPOUND” on page 4.
Note 2:
Among mounted electrical parts on each board, only
parts that are described in the electrical parts list can
be replaced for repairing.
The parts that are not described in the electrical parts
list cannot be replaced with single for repairing.
• Waveforms
– MAIN Board –
1
IC2003
3
(XTAL1)
1 V/DIV, 20 ns/DIV
37 ns
2.9 Vp-p
2
IC2003
<zz,
(MTK_I2S_OUT_MCK)
1 V/DIV, 50 ns/DIV
82 ns
4.2 Vp-p
3
IC2003
<zz.
(MTK_I2S_OUT_BCK)
1 V/DIV, 200 ns/DIV
324 ns
4 Vp-p
20.8
P
s
4 Vp-p
4
IC2003
<zxc
(MTK_I2S_OUT_LRCK)
1 V/DIV, 10
P
s/DIV
5
IC3208
2
(BOOT)
10 V/DIV, 1
P
s/DIV
2
P
s
24.4 Vp-p
6
IC3205
2
(VBST1)
10 V/DIV, 2
P
s/DIV
2.4
P
s
16.8 Vp-p
7
IC3205
qg
(VBST2)
10 V/DIV, 100
P
s/DIV
150
P
s
13.6 Vp-p
Note:
The components identi
fi
ed by mark
0
or
dotted line with mark
0
are critical for safety.
Replace only with part number speci
fi
ed.
Note:
Les composants identi
fi
és par une marque
0
sont critiques pour la sécurité.
Ne les remplacer que par une piéce portant
le numéro spéci
fi
é.
Ver. 1.1
SYS SET
2021/02/16 22:34:59 (GMT+09:00)
