manualshive.com logo in svg

Sony HDV HVR-A1U, Руководство по обслуживанию

Поделиться
Скачать
Sony HDV HVR-A1U Скачать руководство пользователя страница 239

6-80

HVR-A1J/A1U/A1N/A1E/A1P/A1C

3-9.

LED (LED9001)

2.

Attachment procedure

1)

Remove soldering at the two locations 

A

, and install the LED

(LED9001) 

2

 in the FP-031 flexible board.

2)

Roll up the FP-031 flexible board under the LED (LED9001)

1

 with fingertip, and insert the LED top head into the portion

B

 of the LED base. Then route the flexible board in the

specified position.

1.

Removal procedure

1)

Remove the LED (LED9001) and the FP-031 flexible board

1

 from the LED base.

2)

Remove soldering at the two locations 

A

, and remove the LED

(LED9001) 

2

.

B

2

 

LED (LED9001)

Soldering at 2 locations

 

A

  

LED (LED9001)

LED base

•

 

There must be no solder crack.

•

 

There must be no scars and no stains.

•

 

The flexible board must not have any 

    breakdown.

•

 

The retainer plate and LED block must not 

    have any deformation.

1

 LED (LED9001), FP-031 flexible board

FP-031 flexible board

FP-031 flexible board

Direction of the terminal is specified.

Use the rubber finger tip cover.
Lead-free solder
Wire type            :

 

∅

0.6

Soldering iron     : 941 made by Hakko Mfg.
Soldering iron tip: T1-1BC

Soldering iron tip temperature

: 300 

±

10 

°

C

Soldering iron tip contacting time within 
2 sec.

Soldering

LED (LED9001), 
FP-031 flexible board

Points to be noted

Key Points
in Re-assembling

Содержание HDV HVR-A1U






















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды