Sony CDX-454RF - Compact Disc Changer System Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 50

background image

19

CDX-454RF/454XRF

Tracking Offset Check

Connection:

– RF Board (Component Side) –

Procedure:
1. Connect the oscilloscope to TP (TE) and TP (VC) on the RF

board.

2. Put the set into play mode by loading the disc (YEDS-18).
3. Rotate the

[ AMS ]

dial on the wired remote com-

mander, and check the traverse waveform*.

4. Confirm that the oscilloscope waveform is symmetrical on the

top and bottom in relation to 0 V dc, and check this level.

* Traverse waveform: This is the tracking error wave form appears

when crossing the track.

oscilloscope

(DC range)

+
–

TP (VC)

TP (TE)

IC101

A

B

0 V

A=B

traverse waveform
(100 track jump waveform)

VOLT/DIV: 500 mV
TIME/DIV: 2 ms
Center: 0 V

Traverse waveform

.

>

«
...
17
18
19
20
21
...
»

Содержание CDX-454RF - Compact Disc Changer System



















































Отзывы:

Нет отзывов

Похожие инструкции для CDX-454RF - Compact Disc Changer System

Бренд: Harman Kardon Страницы: 54

Бренд: Harman Kardon Страницы: 8

Бренд: Harman Kardon Страницы: 5

Бренд: NAIM Страницы: 26

Бренд: Nakamichi Страницы: 2

Бренд: Teac Страницы: 36

2013 Corsa Infotainment system

Бренд: Vauxhall Страницы: 207

Бренд: Vauxhall Страницы: 101

Бренд: Jamex Страницы: 10

Бренд: Wyrestorm Страницы: 20

Бренд: ICT Страницы: 7

Бренд: Alpine Страницы: 82

Бренд: WCCDYZDTG Страницы: 5

Бренд: Kramer Страницы: 2

Бренд: MOTIVE-RC Страницы: 3

Бренд: Philco Страницы: 39

Бренд: HID Страницы: 2

Бренд: PowerBass Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды