Sony CDX-454RF - Compact Disc Changer System Скачать руководство пользователя страница 23

Страница: 23 / 50

CDX-454RF/454XRF

7-3.

NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

Note on Printed Wiring Board:
•

: parts extracted from the component side.

•

: parts extracted from the conductor side.

•

: internal component.

•

: Pattern from the side which enables seeing.

(The other layers' patterns are not indicated.)

Caution:
Pattern face side:

Parts on the pattern face side seen from

(Conductor Side)

the pattern face are indicated.

Parts face side:

Parts on the parts face side seen from

(Component Side)

the parts face are indicated.

Note on Schematic Diagram:
• All capacitors are in

F unless otherwise noted. pF:

µµ

50 WV or less are not indicated except for electrolytics
and tantalums.

• All resistors are in

Ω

and

W or less unless otherwise

specified.

•

: internal component.

•

: panel designation.

•

: B+ Line.

•

: adjustment for repair.

• Power voltage is dc 14.4V and fed with regulated dc power

supply from CD changer controller.

• Voltages and waveforms are dc with respect to ground

in CD play mode.
no mark : CD PLAY

• Voltages are taken with a VOM (Input impedance 10 M

Ω

Voltage variations may be noted due to normal produc-
tion tolerances.

• Waveforms are taken with a oscilloscope.

Voltage variations may be noted due to normal produc-
tion tolerances.

• Circled numbers refer to waveforms.

• Signal path.

: CD PLAY

Note:
The components identi-
fied by mark

or dotted

line with mark

are criti-

cal for safety.
Replace only with part
number specified.

Note:
Les composants identifiés par
une marque

sont critiques

pour la sécurité.
Ne les remplacer que par une
pièce por tant le numéro
spécifié.

• Circuit Boards Location

SW board

FM board

LSW board

RF board

MAIN board

Содержание CDX-454RF - Compact Disc Changer System



















































Результаты поиска

Содержание CDX-454RF - Compact Disc Changer System

Отзывы:

Похожие инструкции для CDX-454RF - Compact Disc Changer System

Бренды по названию

Популярные бренды

Sony CDX-454RF - Compact Disc Changer System, Руководство по обслуживанию

Результаты поиска

Содержание CDX-454RF - Compact Disc Changer System

Отзывы:

Похожие инструкции для CDX-454RF - Compact Disc Changer System

Бренды по названию

Популярные бренды