Sony CDX-454RF - Compact Disc Changer System Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 50

background image

17

CDX-454RF/454XRF

SECTION 5

MECHANICAL ADJUSTMENTS

• Elevator Height (Address) Adjustment

Note:

This adjustments is necessary when the system controller (IC201),
variable resistor (RV201), slider (R), slider (L), or chassis (ELV)
was replaced for any repair.

Connection:

Adjustment Method:
1. Load a disc magazine, and place the set vertically as shown

below.

2. Connect the regulated power supply, and turn the power on.
3. Press the DISC button on the wired remote commander (RM-

X82RF) and select DISC 5.

4. At this time, if the elevator shaft does not position between

comb teeth A and B at addresses 5 and 6 as shown below,
adjust the following.

5. Press repeatedly the DISC + and – buttons on the wired re-

mote commander (RM-X82RF) so that the elevator shafts
moves from address 6 to address 5, or from 5 to 6. At this
time, adjust RV201 on the main board so that the elevator shaft
positions smoothly between comb teeth A and B.

6. Further, place the set horizontally and make same adjustment

as mentioned above.

7. After adjustment at addresses 5 to 6 is finished, check all op-

erations from addresses 1 to 10 with the set placed vertically
and horizontally respectively to confirm that the elevator shaft
positions in a range between comb teeth A to B.

RV201

comb tooth at address 6

elevator shaft

comb tooth at address 6

comb tooth at address 5

OK

NG

elevator shaft

comb tooth at address 5

A

B

A

B

power supply

(DC 14.4 V)

Compact disc changer

wired remote commander

(RM-X82RF)

GND

+

DISPLAY connector (CN302)

POWER connector (CN303)

«
...
15
16
17
18
19
...
»

Содержание CDX-454RF - Compact Disc Changer System



















































Отзывы:

Нет отзывов

Похожие инструкции для CDX-454RF - Compact Disc Changer System

Бренд: Facit Страницы: 51

Бренд: Kathrein Страницы: 40

Бренд: Salora Страницы: 7

Бренд: UGREEN Страницы: 24

Бренд: Uconnect Страницы: 70

Бренд: Uconnect Страницы: 140

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 67

Бренд: Yamaha Страницы: 54

Бренд: Yamaha Страницы: 70

V665 - RX AV Receiver

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 478

Бренд: Yamaha Страницы: 18

Бренд: Yamaha Страницы: 68

Бренд: Yamaha Страницы: 143

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды