Sony CDX-454RF - Compact Disc Changer System Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 50

background image

3

CDX-454RF/454XRF

SECTION 1

SERVICING NOTES

DISC MAGAZINE GETTING OUT PROCEDURE
ON THE POWER SUPPLY IS OFF

Remove the COVER (LOWER.T) assy beforehand

1) Press the lever (ML.S) to arrow direction.
2) Removal the magazine assy.

Note:

Take out the magazine only when the tray is completely within the

magazine. If the disk or tray is sticking out, turn on the power and
eject the magazine.

NOTES ON HANDLING THE OPTICAL PICK-
UP BLOCK OR BASE UNIT

Lever (ML.S)

Magazine assy

The laser diode in the optical pick-up block may suffer electro-
static breakdown because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.

TEST DISC

This set can playback a CD-R, CD-RW for audio use. When test
this set, use the following test disc.
Test disc for CD-R: TCD-R082LMT (Part No.: J-2502-063-1)

Notes on CD-R/CD-RW discs

You can play CD-Rs (recordable CDs)
designed for audio use on this unit.

Look for this mark to
distinguish CD-Rs for audio
use.

This mark denotes that a
disc is not for audio use.

Some CD-Rs (depending on the equipment
used for its recording or the condition of
the disc) may not play on this unit.

You cannot play a CD-R that is not
finalized

*

.

You cannot play CD-RWs (rewritable CDs).

*

A process necessary for a recorded CD-R disc to
be played on the audio CD player.

power supply cord
(J-2502-058-2)

compact disc changer

RF output cord
(J-2502-058-1)

wirerd remote commander

JIG ON REPAIRING

When repairing this set, connect the jig (cord) for RF output ex-
tract (Part No. J-2502-058-1) and power supply (Part No. J-2502-
058-2) as the figure shown below.

Ver 1.1

«
1
2
3
4
5
...
»

Содержание CDX-454RF - Compact Disc Changer System



















































Отзывы:

Нет отзывов

Похожие инструкции для CDX-454RF - Compact Disc Changer System

Бренд: Zamel Страницы: 34

Бренд: Z3 Technology Страницы: 16

Бренд: X10 Страницы: 5

Бренд: Horizon Hobby Страницы: 23

Бренд: Uni-Art Precise Страницы: 8

Бренд: Aiwa Страницы: 18

Бренд: Rosewill Страницы: 1

Бренд: Jensen Страницы: 32

Бренд: HID Страницы: 2

Бренд: VDO Страницы: 2

HD-RX-4K-x10-C-E

Бренд: Crestron Страницы: 56

Бренд: Audioplex Страницы: 2

Бренд: Dual Страницы: 28

Бренд: Boss Audio Systems Страницы: 8

Бренд: Boss Audio Systems Страницы: 15

Бренд: CYP Страницы: 44

Бренд: Bosch Страницы: 40

LECTUS enroll 5000 MD

Бренд: Bosch Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды