2
GB
This product complies with the “safety, specific rules for powering vertically opening garage doors in residential use” requirements (standard EN
60335-2.95). When installed in line with these instructions and in compliance with the “Installation Checklist”, the product will be compliant with
standards EN 13241-1 and EN 12453.
The instructions referred to in the installation manual and instructions for use of this product are designed to prevent damage to property and
personal injury along with compliance with the above standards. Failure to comply with these instructions absolves Somfy from any liability resulting
from damage that may be caused. Dexxo Pro is a product that must be installed inside the garage with an integrated back-up control system.
Somfy hereby declares thatthe device is compliant with the essential demands and other relevant requirements of directive 1999/5/CE.
A declaration of compliance is available from the web site at
www.somfy.com/CE
(Dexxo Pro).
This product is suitable for use in the European Union and in Switzerland.
GENERAL PRESENTATION
Caution
These are important safety instructions. Always follow the instructions, incorrect installation may lead to serious injury.
Safety instructions
Before installing the motor drive unit, remove all unessential lines or chains and switch off all equipment that is not essential for motorised door
operation.
Before installing the motor drive unit, make sure that the door is in good mechanical condition, that it is properly balanced and that it opens and
closes correctly.
Locate all control systems at least 1.5 metres above floor level, making sure that they are visible from the entrance to the garage but safe from moving
parts.
Position the manual release cord no more than 1.8 metres above floor level.
Whe
re
a removable release mechanism is used, we recommend storing it close to the door.
Fix the label describing the manual release procedure close to the release mechanism.
Fix the warning labels describing the hazards of door motion close to any fixed control mechanisms installed and make sure that the labels are clearly
visible to the user.
After installation, make sure that the mechanism is correctly adjusted and that the motor drive unit reverses its motion when the door encounters
an obstacle that is at least 50 mm from floor level.
After installation, make sure that no part of the door overhangs an area accessible to the public.
After installation, make sure that the motor drive unit inhibits or stops the door opening motion when the door is loaded down with a 20 kg weight
attached to a central position of the door’s bottom edge.
SAFETY INSTRUCTIONS
PRODUCT DESCRIPTION
Product components Fig. 1
Key
Number
Description
Key
Number
Description
1
1
Motor head
14
4
Hex. head M8x12 bolt & washer
2
1
Motor cover
15
6
HU8 nut
3
1 Built-in
light cover
16
2
Shaft
4
1
Lintel bracket
17
2
Circlips
5
1 Door bracket
18
4
Self-tapping
φ
3x10 screw
6
2
Ceiling bracket
19
4
Self-shaping
φ
4x8 screw
7
2
Motor head bracket
20
2
Special screw for plastic
φ
3.5x12
8
1
Manual release cord
21a
1
Single part rail
9
1
Link arm
21b
1
Two part rail
10
2
Travel stop
21b1
1
Sleeve
11
4
Chain retainer pad
21b2
8
Self-shaping
φ
4x8 screw
12
1
Power cable
22
2
Keytis remote control
13
2
Hex. head M8x16 bolt
23
1
230 V 40 W E14 socket light bulb
Types of doors
A:
Projecting up and over door.
B:
Sectional door. If the door surface
exceeds 10 sq. metres
or if the
upper profile
is a specific one, use the sectional door kit, ref.: 2400650.
C:
Swinging door. Use the swinging door kit, ref.: 2400459.
D:
Semi-projecting up and over door (canopy door). Use the semi-projecting up and over door kit, ref.: 2400458.
Fig. 2
5048551A-GB 26/04/07 14:36 Page 2
www.garagedoorsonline.co.uk
01926 463888
www.garagedoorsonline.co.uk
www.garagedoorsonline.co.uk
01926 463888
www.garagedoorsonline.co.uk
