animeo KNX/EIB 4 AC MoCo • REF. 5050779 -
11/31
No.
Object name
Type
Description
36
Mains power failure (230 V)
1 Bit (EIS 1)
With this communication object a mains voltage failure can be signaled.
As soon as the mains voltage precipitates a telegram with the value “1“
it is sent to the bus. With mains voltage return this communication
object sends a telegram with the value “0“.
37
Motor 1 Feedback UP / DOWN
1 Byte (EIS 6)
On these communication objects the current position (UP / DOWN
direction) of the respective blind is sent to the bus based on the
programmed running time. The type of feedback (on demand, status
change, cyclic) is defined in the ETS parameters.
“0“ = UP / “255“ = DOWN
38
Motor 2 Feedback UP / DOWN
1 Byte (EIS 6)
39
Motor 3 Feedback UP / DOWN
1 Byte (EIS 6)
40
Motor 4 Feedback UP / DOWN
1 Byte (EIS 6)
41
Motor 1 Feedback Slat
1 Byte (EIS 6)
On these communication objects the current slat position of the
respective blind is sent to the bus based on the programmed tilting time.
The type of feedback is defined in the ETS parameters. Depending on the
parameter setting on parameter card “General“ the position is defined as
follows:
“255“ = slat maximal closed / “0“ = slat maximal reversed
or
“0“ = slat maximal closed / “255“ = slat maximal reversed
42
Motor 2 Feedback Slat
1 Byte (EIS 6)
43
Motor 3 Feedback Slat
1 Byte (EIS 6)
44
Motor 4 Feedback Slat
1 Byte (EIS 6)
45
Motor 1-4 Status positions
1 Bit (EIS 1)
On this communication object if a telegram with the value “1“ or “0“ is
received, then the current status positions are sent on the bus (objects
37-44).
46
Motor 1 Upper end position
1 Bit (EIS 1)
Over these communication objects for the appropriate blind a telegram
with the value “1” is sent if the upper end position is reached. When
leaving the upper end position of the appropriate blind a telegram with
the value “0” is sent. The upper and the lower end position result from
the parameterised running times.
47
Motor 2 Upper end position
1 Bit (EIS 1)
48
Motor 3 Upper end position
1 Bit (EIS 1)
49
Motor 4 Upper end position
1 Bit (EIS 1)
50
Motor 1-4 Upper end position
1 Bit (EIS 1)
Over this communication object for the blinds 1-4 a telegram with the
value “1” is sent if all 4 blinds have reached the upper end position. If
all 4 blinds have left the upper end position, a telegram with the value
“0“ is sent.
51
Motor 1 Lower end position
1 Bit (EIS 1)
Over these communication objects for the appropriate blind a telegram
with the value “1” is sent after the lower end position is reached. When
leaving the lower end position of the appropriate blind a telegram with
the value “0” is sent. The upper and the lower end position result from
the parameterised running times.
52
Motor 2 Lower end position
1 Bit (EIS 1)
53
Motor 3 Lower end position
1 Bit (EIS 1)
54
Motor 4 Lower end position
1 Bit (EIS 1)
55
Motor 1-4 Lower end position
1 Bit (EIS 1)
Over this communication object for the blinds 1-4 a telegram with the
value “1” is sent after all 4 blinds have reached the lower end position.
After all 4 blinds have left the lower end position, a telegram with the
value “0“ is sent. The upper and the lower end position result from the
parameterised running times.
56
Motor 1 Block functions
1 Bit (EIS 1)
If a telegram with the value “1” is received on one of these communi-
cation objects the functions which are selected in ETS parameters will be
blocked for the appropriate blind. If on one of these communication
objects a telegram with the value “0” is received the functions for the
appropriate blind will be enabled again.
57
Motor 2 Block functions
1 Bit (EIS 1)
58
Motor 3 Block functions
1 Bit (EIS 1)
59
Motor 4 Block functions
1 Bit (EIS 1)
60
Motor 1-4 Block functions
1 Bit (EIS 1)
If a telegram with the value “1” is received on this communication
object the functions which are selected in ETS parameters will be blocked
for the blinds 1-4. If on this communication object a telegram with the
value “0” is received the functions for the blind 1-4 will be enabled
again.
