Solwise 3G11nMRW Скачать руководство пользователя страница 127

Страница: 127 / 257

Version 1.0.15

127

New Password

Enter the new password you want to change.

New Password (Confirm)

Enter the new password again for confirming.

Apply & Cancel

Click

Apply

to continue or

Cancel

to clear the settings on this page.

Note: 1. Only the password can be changed, the user name for administrator is

admin

and not to be changed.

2. If you forget administrator’s password, please reset 3.5G plus WLAN Mobile Server Router to default setting by
pressing the “

Reset

” button on the rear panel o ver 5 seconds. And the password will return to

admin

5.6.2

Upgrade Firmware

There is certain risk while upgrading firmware. Upgrading firmware is not recommended

unless the significant faulty is found. You can upgrade the firmware of 3.5G plus 11n Mobile

Server Router on this page. Make sure the firmware you want to use is on the local hard drive

of the computer. Click

Upgrade Firmware

to proceed.

Update Firmware

Click on

Browse…

button to search your local hard drive and locate the firmware to be

used for update.

Upload & Reset:

Click

Upload

to upgrade the firmware or

Reset

to restore to factory default Settings

Note: 1. To prevent the firmware upgrading interrupted by other wireless signals and caused failure. We

recommend using wired connection to do the upgrading.
2. Before upgrading the fir mware, please remove any USB device which connected with this router.
3.

The firmware upgrade will not remove your previous settings.

Содержание 3G11nMRW


































































































































































































































































Результаты поиска

Содержание 3G11nMRW

Отзывы:

Solwise 3G11nMRW, Руководство пользователя, Страница: 127 / 257

Результаты поиска

Содержание 3G11nMRW

Отзывы: