manualshive.com logo in svg

Solowave Big Backyard F23230, Руководство по сборке, Страница: 9 / 28

Поделиться
Скачать
Solowave Big Backyard F23230 Скачать руководство пользователя страница 9

Flat Washer

Hex Bolt Assembly

Hex Bolt

Lock Washer

Wood  Parts

T-Nut

Tap T-Nut

into the hole.

Wood  Parts

Leave this

hole open

1 x 6 x 38-1/4"

Floor End 

Hole is for

1/4 x 2" Hex Bolt 

1/4 x 1-1/2"

Lag Screw

& 1/4" Flat Washer 

(Pre-drill with 3/16"

drill bit before 

fastening Lag Screw)

HARDWARE LIST

2 pcs 1/4 x 5" Hex Bolt

18 pcs 1/4 x 2" Hex Bolt

20 pcs 1/4" T-Nut

24 pcs 1/4" Flat Washer

20 pcs 1/4" Lock Washer 

4 pcs 1/4 x 1-1/2" Lag Screw

WOOD PARTS LIST

2 pcs 2x3x35" Ground Diagonal

2 pcs 1x5x 56" Ground Side

4 pcs 2x4x83" Post

2 pcs 1x6x 38-1/4" Floor End
2 pcs 1x4x 47-3/4" Roof Side

Lag Screw

Flat Washer

Lag Screw Assembly

3/16" 

Pre-drill hole

Factory 

drilled hole

Slide Wall

Swing Wall

Hex Bolt

1/4 x 2" 

Diagona

Ground 

2 x 3 x 35"

Posts

2 x 4 x 83" 

1/4 x 5"

Hex Bolt 

l

Roof Side 

1 x 4 x 47-3/4"

1 x 5 x 56"

Ground Side 

1

DO NOT OVER-TIGHTEN HEX BOLTS!

Hardware should not crush wood.

Swing & Slide Wall Assembly

For the Slide Wall, assemble Ground Diagonal to Post;  Roof Side, Floor End 

& Ground Side to Posts; Ground Diangonal to Ground Side.

NOTE:  For the Swing Wall Assembly, the layout is opposite the Slide Wall, 

make sure to repeat the above step.

9

Содержание Big Backyard F23230





























Отзывы:

Нет отзывов