Solowave Big Backyard F23230 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 28

Solowave Big Backyard F23230 Скачать руководство пользователя страница 6

(6) 5/16 x 4-1/2" Hex Bolt

(5) 3/16" Flat

Washer

(4) 3/8" Flat Washer

(5) #8 x 1"

Pan Screw

CLIMBING ROCK BAG

(4) 5/16 x 4" Hex Bolt

(4) 3/8 x 3" Lag Screw

HARDWARE IDENTIFICATION

Before you start assembling your fort, be sure to sort, identify, and count all of

the hardware.

During Assembly DO NOT fully tighten bolts unless instructed. Fully

tightened bolts may not allow for other hole alignments.

IMPORTANT! Before children use the play center, make sure all

hardware is tightened, all ground stakes are installed, and any

remaining wood, hardware packaging materials are removed

from the play area.

Be careful not to over-tighten hardware as it will crush wood fibers

and result in splintering.

THESE PARTS ARE ACTUAL SIZE

(6) Plastic Tie

(5)1/4" Barrel Nut

(No Prongs)

(4) Swing Hangers

(2) Glider Hangers

(Not to Scale)

(5) 1/4" Lock

Washer

(4) 1/4 x 5-1/2" Hex Bolt

(2) 5/16 x 2" Hex Bolt

(5)1/4 x 1-1/4"

Pan Bolt

6

«
...
4
5
6
7
8
...
»

Содержание Big Backyard F23230





























Отзывы:

Нет отзывов