manualshive.com logo in svg

Solowave Big Backyard F23230, Руководство по сборке, Страница: 10 / 28

Поделиться
Скачать
Solowave Big Backyard F23230 Скачать руководство пользователя страница 10

1 x 4 x 35¾"

(Pre-drill 

Tarp Front

Wood Screw

Floor Joist)

1/4 x 1¼"

(Is thinner than

with 1/8 Drill)

Hex Bolt 

Pan Bolt 

Centre Divider

1 x 4 x 58½"

#8 x 1½"

Roof Side

1/4 x 2"

Make sure that Floor Front holes are 

Hardware should not crush wood

oriented toward the ground & to the right.

DO NOT OVER-TIGHTEN BOLTS!

2A

Front Wall Assembly

With the aid of helper, attach Floor Front, Ground Front, 

Front Top to Walls created in Step 1.

IMPORTANT! 

Attach Centre Divider to Floor Front &

Front Top. Fasten the Tarp Front to the Roof Sides.

Ground Front

1/4 x 4"

Hex Bolt 

towards the ground)

required) 

(Holes are positioned 

Hex Bolt 

1/4 x 4"

1 x 4 x 58¼"

Front Top

1 x 5 x 59¼"

2 x 3 x 58¼"

Floor Front

1/4 x 2½"

Lag Screw

(Pre-drilling

Wood  Parts

Flat Washer

Hex Bolt Assembly

T-Nut

Hex Bolt

Tap T-Nut

into the hole.

Wood  Parts

Lock Washer

Lag Screw)

drill bit before fastening

(Pre-drill with 3/16'

HARDWARE LIST

1 pc 1/4x2" Hex Bolt

2 pcs 1/4x5" Hex Bolt
4 pcs 1/4x4" Hex Bolt

2 pcs 1/4x2-1/2" Lag Screw

8 pcs 1/4" T-Nut

10 pcs 1/4" Flat Washer

8 pcs 1/4" Lock Washer

1 pc 1/4x1-1/4" Pan Bolt

4 pcs #8x1-1/2" Wood Screw

WOOD PARTS LIST

1 pc 1x4x 58-1/2" Tarp Front

1 pc 2 x3x58-1/4" Floor Front

1 pc 1 x5x59-1/4" Ground Front

1 pc 1 x4x58-1/4" Front Top

1 pc 1 x4x35-3/4" Centre Divider

Lag Screw

Flat Washer

Lag Screw Assembly

3/16" 

Pre-drill hole

Factory 

drilled hole

1/4 x 5"

Hex Bolt 

Note: 

Middle Hole is

being used in 

the Post 

10

Содержание Big Backyard F23230





























Отзывы:

Нет отзывов