Solowave Big Backyard F23230 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 28

Solowave Big Backyard F23230 Скачать руководство пользователя страница 3

Tools Required

Shovel

Swing Hangers

Swing hangers must be screwed into the wood
the full length of the shaft, so that the triangular
head is touching the wood (see swing hanger
diagram). Failure to correctly install swing hangers
may result in the hanger itself breaking, or the
hanger becoming dislodged from the wood.
Either circumstance can cause serious injury. Big
Backyard cannot assume any responsibility for
incorrect installation of swing hangers.
(Liquid soap may be used as a lubricant for ease
of installation).

NOTE: Follow proper assembly procedure.

Warning: For your child’s safety orientate the swing

hangers as shown to ensure your swing will have the proper
swinging motion when installed. Failure to do so could result in
the premature breaking off of the swing hanger or swing chain.

Hardware

When making the selection of 1/4” and 5/16”
hardware, carefully read the instructions in each
step of this manual to ensure the proper hardware
is used.

NOTE: 5/16” Hardware is larger in diameter than 1/4”.

The Swing Triangle Plate has a total of 5 holes,
and they are all used depending on where you are
installing it. When installing the plates, pay close
attention to the holes required. When complete,
the swing end should be angled out (away from
fort) approx. 110˚

NOTE: In the event that the thread of a Hex Bolt is

exposed beyond the tee-nut, please disassemble, add

another flat washer to head of hex bolt and reassemble.

Tee - Nuts & Lock washers

Place tee-nut in hole and tap into place with
hammer. Insert the hex bolt through, first the
lock washer and then the flat washer, and feed
through hole. Hand tighten to ensure bolt and
tee-nut connection (this may not be possible due
to coating on hardware, if not use a ratchet), and
then proceed with ratchet. DO NOT over tighten.
Hardware should not crush wood.

NOTE: A 1/4” lock washer and flat washer, are used with

1/4” hex bolt or 5/16” with 5/16”.

Dowel Installation

1. Insert Dowel into provided holes until the

shoulder of tenon is flush to the face of the
Swing Rail or Access Rail or
Ladder Post.

2. Pre-drill a 3 x 1/8” hole through Rail or Post

prior to securing with wood screw. Securing with
screw prior to pre-drilling may lead to cracking
and must be avoided.

3. Secure dowel in place with approprate wood

screws and instructed within manual

.

Swing Hanger

Swing Hanger

Screw Hanger in until

it is snug and flush with

bottom of Swing Beam.

Swing Hanger orientation for

swing attachment.

Swing Beam

Swing Beam

Dowel

Rail

1/8” Drill Bit

Shoulder

Tenon

Level

#2 & #3 Phillips

or Robertson

Safety

Glasses

Drill (1/8”

3/16” Bit)

Measuring

Tape

Hammer

Ratchet 1/2”,

7/16” & 9/16”

Hex Bolt

Lock Washer

Flat Washer

Wood

Tee-Nut

© Solowave Design. All rights reserved.

Important Information: Please ensure page is read.

HELPFUL HINTS

Square

Ruler

Step

Ladder

«
1
2
3
4
5
...
»

Содержание Big Backyard F23230





























Отзывы:

Нет отзывов