Solowave Big Backyard F23230 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 28

Solowave Big Backyard F23230 Скачать руководство пользователя страница 14

Chalk Wall

(Tarp)

5

Attach Panel Frame and Lower Chalk Wall with

(4) Wood Screws. Drill pilot holes with a 1/8" drill bit,

using the boards as guides.

Lower Chalk Wall should butt up under Panel Frame

end. Next, attach the Lower Chalk Wall from the inside

with (2) Wood Screws into the divider from the inside.

Hang Chalk Wall with graphics facing inside, and

attach with (10) Pan Screws (#8 Flat Washers)

from the outside. With the remaining (2) Pan Screws

(#8 Flat Washers), attach to the divider from the inside.

Important! Loosen the bolts from the Centre Divider to

slide tarp between. Tighten bolts.

Wood Screw

Lower Chalk Wall

1 x 2 x 25½"

Wood

Panel Frame

Screw

1 x 4 x 31"

#8x 1-1/8"

#8 x 1½"

Gap between deck

and bottom can not

exceed 3 inches.

Evenly space

#8 x 1/2"

Attach through

Chalk Wall hem.

Pan Screws.

HARDWARE LIST

2 pcs #8x1-1/8" Wood Screw
4 pcs #8x1-1/2" Wood Screw

12 pcs #8x1/2" Pan Screw

12 pcs #8 Flat Washer

WOOD PARTS LIST

1 pc 1x2x25-1/2" Panel Frame

1 pc 1x4x31" Lower Chalk Wall

ACCESSORY LIST

1 Chalk Wall (Tarp)

14

«
...
12
13
14
15
16
...
»

Содержание Big Backyard F23230





























Отзывы:

Нет отзывов