manualshive.com logo in svg

Solowave Big Backyard F23230, Руководство по сборке, Страница: 22 / 28

Поделиться
Скачать
Solowave Big Backyard F23230 Скачать руководство пользователя страница 22

1"

9B

View from under Fort

Centre and hang Canopy over Roof Ridge & attach (2) pan screws 

with washers on the top of roof. Stretch Canopy to the front & 

attach with (4) evenly spaced screws with washers at the hem.  

Do the same at the back.

Make sure this

knot is tight to

10 pcs #8x1/2"Pan Screw

10 pcs #8"Flat Washer

ACCESSORY LIST

1 Canopy

than 9-1/2"

Plastic Ties.

before attaching 

the Floor Back

Must be greater 

HARDWARE LIST

HARDWARE LIST

6 Plastic Ties

ACCESSORY LIST

1 Rope Ladder

Loosen bolt

to get tarp

underneath

#8 x 1/2" Pan Screw

   #8 Flat Washer

10

A

B

Keep rope tight to remove slack

Plastic Ties.

Keep 1" space between 

A. Pull rope through holes at top 

and tie a knot under deck. Spacing 

between top rung and edge of 

board must be greater than 9-1/2"

B. Pull rope through hole at bottom 

and tie knot, making sure that 

spacing between rung and edge of 

board is greater than 9-1/2".

C. IMPORTANT! use (6)plastic ties 

tighten loose rope ends at top of 

rope ladder, and cut excess Plastic 

Ties, making sure to round the sharp 

edges.  

C

22

Содержание Big Backyard F23230





























Отзывы:

Нет отзывов