background image

27 

 

A qualified service agency should conduct an annual inspection and maintenance of your Solas Fireplace 
Insert including the overall installation and venting to keep it running safely.  The following procedures 
should be performed only by a qualified service person. The gas supply should be turned off and the stove 
should be completely cool whenever a maintenance procedure is performed. All parts of the appliance that are 
removed for servicing must be replaced prior to operation.   

WARNING:    Do  not  operate  the  appliance  with  the  glass  front  removed,  cracked  or  broken. 
Replacement of the glass should be done by a qualified service person.

 

WARNING:  Use only glass assembly, P/N 36-510 which includes the glass panel, frame and gasket.  
Do not use substitute materials.  Do not strike or slam the glass front. The appliance area must be 
kept clear and free from combustible materials, gasoline and other flammable vapors and liquids. 
 
REPLACING THE GLASS

 

The glass mounting system consists of the glass panel, special glass gasket and the metal glass frame.  
Should the glass need to be replaced, you must replace the entire glass/glass frame assembly (PN 36-510). 
See page 30 for information on obtaining replacement parts. Use the following procedure and refer to the 
illustrations on page 16 of this manual. 
1.  Turn the fireplace completely off and allow it to cool to room temperature. 
2.  Remove the fireplace surround. See instructions on page 18. 
3.  If the glass is broken, be sure to wear gloves and eye protection. 
4.  Remove the glass frame retaining clips from the top edge of the glass frame. 
5.  This will allow the glass frame to tip slightly forward. The glass may be  loose in the frame, so it is very 

important to support both the glass and the frame when handling.  Place your thumbs on the outside of 
the glass frame and wrap your fingers around the frame and onto the glass.  Squeeze the frame and glass 
while moving. Carefully lift the glass frame and glass up and off the fireplace.  Set the glass and frame 
aside on a padded surface.  If the glass is broken, do this over spread out newspaper to catch all loose 
material.  Wrap the old glass frame, glass and gasket in several layers of newspaper and discard.   

Installing the replacement glass/glass frame assembly. 

1.  Unpack the new glass/glass frame assembly taking care when handling. 
2.  Carefully pick up the glass and glass frame assembly by grasping the sides of the frame and using your 

thumbs and fingers to hold the glass in place within the gasket and frame. 

3.  With the glass frame (and glass) at a slight angle (leaving room for your fingers between the frame and 

the firebox) insert the bottom edge of the frame into the frame retainer located on the bottom front of 
the firebox.  Take care to center the frame from left to right.  Once the bottom edge is in place, move 
your fingers out of the way and press the top of the frame against the firebox while pushing down to be 
sure the frame is fully engaged in the frame retainer.  Hold the frame in place with one hand and rein-
stall the glass frame fasteners, leaving them loose. 

4.  Tighten the glass frame fasteners in stages working from the center out.  Continue the process until all 

fasteners are uniformly tight.  Do not over-tighten the fasteners. 

5.  Replace the fireplace surround. See instructions on page 18. 

CLEANING THE GLASS & INNER PORCELAIN ENAMEL PANELS 
WARNING:  Never clean the glass or panels while they are hot.  Do not use abrasive cleaners or 
cleaners containing ammonia. 
   
NOTE:  A micro-fiber cleaning cloth and plain water is recommended by the glass manufacturer. 

MAINTENANCE 

Содержание FIN-36N



































Отзывы: