SolarEdge SE10KUS Скачать руководство пользователя страница 63

Страница: 63 / 101

Meter Status

Meters

Export

– RS485-2 Modbus ID #2

Status: OK

Type and function

: Displays the meter functionality (Production, Export, Import,

Import)

Status: Displays OK if the meter is communicating with the inverter

<Error message>: If there is a meter error, it is displayed in this line.

Power

: Depending on the meter type connected to the inverter, this line

displays the exported or imported power

Energy: The total energy read by the meter. The value displayed in this line

depends on the meter type connected to the inverter and its location:

If a bidirectional meter is connected at the consumption point, this

value is the consumed energy.

If the meter is installed at the production connection point, this value is

the energy produced by the site.

If the meter is installed at the grid connection point, this value is the

energy exported to the grid.

NOTE

This data is accumulated according to an internal real-time

clock.

Three

Phase

System

Installation

Guide

MAN-01-00527-1.

Viewing System Status

Содержание SE10KUS






































































































Результаты поиска

Содержание SE10KUS

Отзывы:

Похожие инструкции для SE10KUS

Бренды по названию

Популярные бренды

SolarEdge SE10KUS, Руководство по установке

Результаты поиска

Содержание SE10KUS

Отзывы:

Похожие инструкции для SE10KUS

Бренды по названию

Популярные бренды