SolarEdge SE10KUS Скачать руководство пользователя страница 55

Страница: 55 / 101

1. Select the Communication menu to define and configure the following:

The communication option used by the inverter to communicate with the

monitoring platform

The communication option used to communicate between multiple

SolarEdge devices or other external non-SolarEdge devices, such as

electricity meters or loggers.

2. Tap the Server red arrow to set the communication method to be used for

communication between devices and the SolarEdge monitoring platform. The

default is LAN.

NOTE

The Server menu shows only the communication options installed in the

inverter.

For detailed information about all the configuration options, refer to the
Communication Options Application Note, available on the SolarEdge
website at

https://www.solaredge.com/sites/default/files/solaredge-

communication_options_application_note_v2_250_and_above.pdf

Power Control

Power control options are detailed in the

Power Control Application

Note, available on the SolarEdge website at .

The Grid Control option may be disabled. Enabling it opens additional

options in the menu.

The Energy Manager option is used for setting power export limitation,

as described in the

Export Limitation Application Note, available on the

SolarEdge website at

https://www.solaredge.com/sites/default/files/export_

limitation_application_note_NA.pdf

For P(Q) diagram refer to

https://www.solaredge.com/sites/default/files/application_note_p_q_diagram_of_

se_inverters_en_and_na.pdf

Three

Phase

System

Installation

Guide

MAN-01-00527-1.

Step 2: Commissioning and Configuring the Installation

Содержание SE10KUS






































































































Результаты поиска

Содержание SE10KUS

Отзывы:

Бренды по названию

Популярные бренды

SolarEdge SE10KUS, Руководство по установке

Результаты поиска

Содержание SE10KUS

Отзывы:

Бренды по названию

Популярные бренды