SNAIGE KGC310A+, Инструкция по эксплуатации

Страница: 8 / 36

POSITIONING
 Place the appliance in a dry, well ventilated room.
 WARNING! The appliance should not be operated in an unheated room or porch. Place the
appliance away from heat sources such as kitchen stove/oven, radiators, or direct sunlight.
 WARNING! The appliance must not touch any pipes for heating, gas or water supply, or
any other electrical devices.
 Do not cover the ventilation holes at the top of the appliances– it must be a good air circulation
around the appliance. There should be a gap of at least 10 cm between the top of the appliance
body and any furniture that may be above it (fig. 5). If this requirement is not followed, the
appliance consumes more electrical energy and its compressor may overheat.
 If the appliance is placed in a corner, a gap of at least 1 cm must be left between the appliance
body and the wall so that the freezer compartment door can be opened enough to pull out the
frozen product drawer (fig. 6).
 The appliance must stand on a level surface and must not touch the wall. If necessary, regulate the
height of the appliance by adjusting the levelling feet: by turning them clockwise – the front of the
appliance rises, by turning them counter clockwise – it comes down. If the appliance is tilted slightly
backward – the doors will close by themselves.
CHANGING THE OPENING DIRECTION OF THE DOORS
It is recommended that changing the opening direction of the doors should be done with a helper.
You will need two spanners No. 8 and No. 10 and a Philips head screwdriver.
! When changing the opening direction of the doors, YOU CAN NOT lay the refrigerator horizontally.
Do the actions below in the order they are listed (fig. 11):
WARNING! Turn off the appliance and pull the plug out of the electricity supply socket.
1. Remove the bottom cover 15. Unscrew two screws 12 and remove the bottom bracket 13
together with the washers 11 on the axle and the spacer 10. Remove the bottom door 9.
2. Uncrew the fixing screws 7 of the middle bracket 6. Remove the middle bracket 6 together with
with washers on the axle and the spacer 5. Remove the top door 4.
3. Unscrew the axle 2 together with the nut 1 and the washers 3 from the upper bracket and screw
all this set on the left side of the door. Displace the plug 21 the upper door and the plug 19 from
the bottom door on the right side.
4. Take out the pins 20 from the cabinet in the zone of the cross element and displace the to the
right side. Hang the upper door on the axle 2.
5. Prior to screwing the middle bracket 6 with washers and spacers on the left side of the cabinet,
insert the bracket axle into the upper door. Hang the bottom door on the middle bracket axle.
6. Prior to unscrewing the bracket 16 and exchanging it with the bottom bracket 13 (together with
the set of washers and spacers), insert the bracket axle into the bottom door. The brackets 14
which are under the brackets 13 and 16 remain in their places.
7. Unscrew fixing screws 17 from doors, remove handles 18 and screw it on the eight side of the
door therefore taken out plugs. Cover the holes in which the handle was screwed with taken out
plugs.
CHANGING THE INTERIOR LIGHT BULB
When changing the interior light bulb (7 fig.), do the actions below in the order they are listed:
1. Unplug the appliance from the mains by pulling the plug out of the electricity supply socket.
2. Push the interior light bulb lid retainer to the right with a flat screwdriver and with your other
hand pull it down.
3. First check whether the bulb has really burnt out: unscrew it and screw it back in. Plug the
appliance into the electricity supply. If the bulb lights up, it is not necessary to change it.
4. If the bulb does not light up, replace it with another 15 W bulb of the same type with an E14 lamp
holder.
5. When the bulb is replaced, first put the lamp lid in the right position, then on the left side push up
until the lid fixes in position.
6. Plug the appliance into the electricity supply socket.
GB
6