Smithco 76-000-D Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 116

background image

94

Ser
vice

HY13-1527-M1/US

Torqmotor™ Service Procedure

TF, TG, TH and TL Series

Parker Hannifin Corporation

Hydraulic Pump/Motor Division

Greeneville, TN 37745 US

25

Remove shaft
seal, backup
washer & backup
ring

17. Remove shaft seal (16), backup ring (17),

and backup washer (25) from housing
by working them around unseated thrust
washers (14) and thrust bearing (15) and out
of the housing. Discard seal and washers.
SEE FIGURE 21.

NOTE

NOTE: The original design units of
Torqmotors™ did not include backup
washer (25), but must include backup
washer (25) when reassembled for
service.

Remove dirt &
water seal

18. Remove housing (18) from vise, invert it and

remove and discard dirt & water seal (20). A
blind hole bearing or seal puller is required.
SEE FIGURE 22.

Inspect housing
assembly

19. Inspect housing (18) assembly for cracks,

the machined surfaces for nicks, burrs,
brinelling or corrosion. Remove burrs
that can be removed without changing
dimensional characteristics. Inspect tapped
holes for thread damage. SEE FIGURE 23.
If the housing is defective in these areas,
discard the housing assembly.

Figure 21

Figure 22

Figure 23

Disassembly and Inspection

76-238 DISASSEMBLY INSTRUCTIONS

«
...
94
95
96
97
98
...
»

Содержание 76-000-D





















































































































Отзывы:

Нет отзывов

Похожие инструкции для 76-000-D

Бренд: Tanaka Страницы: 10

Бренд: Garland Страницы: 124

Optimax 9170-03-59

Бренд: Little Wonder Страницы: 14

Бренд: Gaggenau Страницы: 28

Бренд: Columbus Страницы: 80

Бренд: Tuff & Gusty Страницы: 4

Бренд: Silvercrest Страницы: 20

Бренд: Silvercrest Страницы: 27

Бренд: Silvercrest Страницы: 34

Бренд: Silvercrest Страницы: 34

Sno-Thro 938000

Бренд: Ariens Страницы: 24

924 SNO-THRO 924108

Бренд: Ariens Страницы: 29

Бренд: Ariens Страницы: 16

Бренд: Ariens Страницы: 36

Бренд: Daewoo Страницы: 28

Бренд: Yardworks Страницы: 25

Бренд: EarthWise Страницы: 21

Бренд: Mahindra Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды