Smithco 76-000-D Скачать руководство пользователя страница 87

Страница: 87 / 116

Ser

vice

76-238 TROUBLESHOOTING CHECKLIST

HY13-1527-M1/US

Torqmotor™ Service Procedure

TF, TG, TH and TL Series

Parker Hannifin Corporation

Hydraulic Pump/Motor Division

Greeneville, TN 37745 US

Troubleshooting Checklist

1. Hose fittings loose, worn or
damaged.

2. Oil seal rings (4) deteriorated by
excess heat.

3. Special bolt (1, 1A, 1B or 1C)
  loose or its sealing area
  deteriorated by corrosion.

4. Internal shaft seal (16) worn or
damaged.

5. Worn coupling shaft (12) and
internal seal (16).

Oil Leakage

Check & replace damaged
fittings or “O” Rings. Torque to
manufacturers specifications.

Replace oil seal rings by disassembling
Torqmotor™ unit.

(a) Loosen then tighten single bolt to

torque specification.

(b) Replace bolt.

Replace seal. Disassembly of Torqmotor™
unit necessary.

Replace coupling shaft and seal by
disassembling Torqmotor™ unit.

Significant loss of
speed under load

1. Lack of sufficient oil supply

2. High internal motor leakage

3. Severely worn or damaged
internal splines.

4. Excessive heat.

(a) Check for faulty relief valve and

adjust or replace as required.

(b) Check for and repair worn pump.

temperature of operation.

Replace worn rotor set by disassembling
Torqmotor™ unit.

Replace rotor set, drive link and coupling
shaft by disassembling Torqmotor™ unit.

Locate excessive heat source (usually a
restriction) in the system and correct the
condition.

Low mechanical
efficiency or un-
due high pressure
required to operate
Torqmotor™ unit

1. Line blockage

2. Internal interference

3. Lack of pumping pressure

4. Excessive binding or loading in
system external to Torqmotor™
unit.

Locate blockage source and repair or
replace.

Disassemble Torqmotor™ unit, identify and
remedy cause and repair, replacing parts
as necessary.

Check for and repair worn pump.

Locate source and eliminate cause.

CAUTION: If the hydraulic system fluid becomes overheated [in excess of 200°F (93.3°C)], seals in the
system can shrink, harden or crack, thus losing their sealing ability.

Trouble

Cause

Remedy

Содержание 76-000-D





















































































































Результаты поиска

Содержание 76-000-D

Отзывы:

Похожие инструкции для 76-000-D

Бренды по названию

Популярные бренды

Smithco 76-000-D, Запчасти и обслуживание

Результаты поиска

Содержание 76-000-D

Отзывы:

Похожие инструкции для 76-000-D

Бренды по названию

Популярные бренды