Smithco 76-000-D Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 116

background image

92

Ser
vice

HY13-1527-M1/US

Torqmotor™ Service Procedure

TF, TG, TH and TL Series

Parker Hannifin Corporation

Hydraulic Pump/Motor Division

Greeneville, TN 37745 US

23

NOTE

NOTE: Series TG or TH may have a
rotor set with two stator halves (8B &
8D) with a seal ring (4) between them
and two sets of seven vanes (8C & 8E).
Discard seal ring only if stator halves
become disassembled during the service
procedures.

NOTE

NOTE: A polished pattern on the wear
plate from rotor rotation is normal.

Check rotor,
vane clearance

11. Place rotor set (8) and wear plate (9) on a

flat surface and center rotor (8A) in stator
(8B) such that two rotor lobes (180 degrees
apart) and a roller vane (8C) centerline are
on the same stator centerline. Check the
rotor lobe to roller vane clearance with a
feeler gage at this common centerline. If
there is more than .005 inches (0.13 mm) of
clearance, replace rotor set. SEE FIGURE
15.

NOTE

NOTE: If rotor set (8) has two stator
halves (8B & 8D) and two sets of seven
vanes (8C & 8E) as shown in the alternate
construction TG rotor set assembly
view, check the rotor lobe to roller vane
clearance at both ends of rotor.

Remove &
inspect
drive link

12. Remove drive link (10) from coupling shaft

(12) if it was not removed with rotor set and
wear plate. Inspect drive link for cracks and
worn or damaged splines. No perceptible
lash (play) should be noted between mating
spline parts. SEE FIGURE 16. Remove and
discard seal ring (4) from housing (18).

Remove thrust
bearing

13. Remove thrust bearing (11) from top of

coupling shaft. Inspect for wear, brinelling,
corrosion and a full complement of retained
rollers. SEE FIGURE 17.

Figure 17

Figure 16

Figure 15

Figure 14

Disassembly and Inspection

76-238 DISASSEMBLY INSTRUCTIONS

«
...
92
93
94
95
96
...
»

Содержание 76-000-D





















































































































Отзывы:

Нет отзывов

Похожие инструкции для 76-000-D

Бренд: Boss Snowplow Страницы: 28

Бренд: Ryobi Страницы: 19

Бренд: Poulan Pro Страницы: 44

Бренд: Amrobt Страницы: 32

Бренд: McCulloch Страницы: 40

Бренд: Echo Страницы: 5

Бренд: Stark Страницы: 23

Бренд: Kärcher Страницы: 17

Бренд: Kärcher Страницы: 298

Бренд: hecht Страницы: 44

Бренд: TOOLCRAFT Страницы: 28

Бренд: American-Lincoln Страницы: 76

Бренд: Dolmar Страницы: 44

Бренд: Partner Страницы: 64

QUIET BLOW QB1100HPN

Бренд: Billy Goat Страницы: 3

Бренд: Fujioh Страницы: 24

Бренд: Jonsered Страницы: 60

7800001 EI75225

Бренд: Snapper Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды