Smithco 76-000-D Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 116

background image

11

Ser

vice

ADJUSTMENTS

PARK BRAKE ADJUSTMENT

By turning knob on end of park brake lever you can tighten or loosen brake a

small amount. To tighten turn the knob clockwise. To loosen turn counter clock

-

wise. If this is not enough turn clevis on brake cable to adjust length of cable.

STEERING CHAIN ADJUSTMENT

Steering Sprockets (A) should be level with each other. Check with straight

edge. Make any adjustments. Slide Idler Pulley (B) so that it is snug onto the

chain. Tighten all nuts and bolts in place.

WHEEL 'CREEP' ADJUSTMENT

‘Creep’ is when engine is running and hydrostatic transmission is in neutral, but

due to inadequate alignment, wheels still move. Do the following procedures to

stop this motion.
1. Lift up and support the unit so rear wheels are off the ground and can turn

freely.

2. On the side of hydrostatic transmission is the Shift Arm (C) . In the ‘V’

shaped notch of shift arm rests and Idler Pulley (D). This Pulley is mounted

on an Idler Arm (E).

3. Loosen bolt and nut holding Pulley to Idler Arm. Leave finger tight.
4. With engine running, slide the Pulley in Idler Arm slot until it centers on

Shift Arm on hydrostatic and wheel ‘creep’ stops.

5. Tighten all fasteners and test by using foot pedal linkage to see that the

‘creep’ is removed.

6. Turn the engine off and lower the machine.

Do not lift reel head while engage. Disengage reel before lifting or lowering.

STORAGE

When storing, remove the key from the key switch to avoid unauthorized persons from operating machine.
  1.  Before storing clean machine thoroughly.
  2.  Check bolts and nuts, tighten as necessary.
  3.  Make all repairs that are needed and remove any debris.
  4.  Remove the battery, adjust the electrolyte level and recharge it. Store the battery in a dry, dark place.
  5.  Store in a clean and dry area, but NOT near a stove, furnace or water heater which uses a pilot light or

any device that can create a spark.

6. Engines stored over 30 days need to be protected or drained of fuel to prevent gum from forming in a

fuel system or on essential carburetor parts. Check the engine manual and follow the instructions for

the storage of the engine.

«
...
11
12
13
14
15
...
»

Содержание 76-000-D





















































































































Отзывы:

Нет отзывов

Похожие инструкции для 76-000-D

Бренд: Haaga Страницы: 7

Бренд: HOLMS Страницы: 21

Бренд: Ariens Страницы: 58

Бренд: Ariens Страницы: 8

Бренд: AP&T Страницы: 3

Бренд: Poulan Pro Страницы: 32

Бренд: Cub Cadet Страницы: 28

TrimmerPlus ST720r

Бренд: MTD Страницы: 36

Бренд: Cub Cadet Страницы: 32

Бренд: Gardebruk Страницы: 34

Бренд: Holder Страницы: 21

Бренд: Johnny Vac Страницы: 12

Бренд: Toro Страницы: 124

Бренд: Elektror Страницы: 52

Бренд: Iron Baltic Страницы: 22

QUIET BLOW QB1004

Бренд: Billy Goat Страницы: 12

Бренд: Billy Goat Страницы: 28

QUIET BLOW QB553HC

Бренд: Billy Goat Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды