Smithco 76-000-D Скачать руководство пользователя страница 90

Страница: 90 / 116

Ser
vice

76-238 DISASSEMBLY AND INSPECTION

HY13-1527-M1/US

Torqmotor™ Service Procedure

TF, TG, TH and TL Series

Parker Hannifin Corporation

Hydraulic Pump/Motor Division

Greeneville, TN 37745 US

Preparation Before Disassembly

• Before you disassemble the Torqmotor™ unit or any of its components read this entire manual. It provides

important information on parts and procedures you will need to know to service the Torqmotor™.

• Determine the type of end construction from the alternate views shown on the exploded view.

• The Series TF, TG, TL & TH Torqmotors™ will have a 5 inch (127.9 mm) main body outside diameter and seven

3/8 24 UNF 2A cover bolts.

• Refer to “Tools and Materials Required for Services” section for tools and other items required to service the

Torqmotor™ and have them available.

• Thoroughly clean off all outside dirt, especially from around fittings and hose connections, before disconnect-

ing and removing the Torqmotor™. Remove rust or corrosion from coupling shaft.

• Remove coupling shaft connections and hose fittings and immediately plug port holes and fluid lines.

• Remove the Torqmotor™ from system, drain it of fluid and take it to a clean work surface.

• Clean and dry the Torqmotor™ before you start to disassemble the unit.

• As you disassemble the Torqmotor™ clean all parts, except seals, in clean petroleum-based solvent, and blow

them dry.

WARNING: petroleum-base solvents are flammable. Be extremely careful when using any solvent. Even a small
explosion or fire could cause injury or death.

WARNING: WEAR EYE PROTECTION AND BE SURE TO COMPLY WITH OSHA OR OTHER MAXIMUM AIR
PRESSURE REQUIREMENTS.

CAUTION: Never steam or high pressure wash hydraulic components. Do not force or abuse closely fitted parts.

• Keep parts separate to avoid nicks and burrs.

• Discard all seals and seal rings as they are removed from the Torqmotor™. Replace all seals, seal rings and

any damaged or worn parts with genuine Parker or OEM approved service parts.

Disassembly and Inspection

Содержание 76-000-D





















































































































Результаты поиска

Содержание 76-000-D

Отзывы:

Похожие инструкции для 76-000-D

Бренды по названию

Популярные бренды

Smithco 76-000-D, Запчасти и обслуживание

Результаты поиска

Содержание 76-000-D

Отзывы:

Похожие инструкции для 76-000-D

Бренды по названию

Популярные бренды