SMC Networks ZK2-ZSV-A Series Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 57

background image

-33-

NO.ZK2-OM00501-B

■

[F11] Display resolution

This function is used to change the pressure display resolution.
This can be used to prevent the digits from flickering on the display.

<Operation>

Press the

or

button in function selection mode to display [F11].

Press the

button.

Move on to setting of display resolution.

Press the

button to set.

Return to function selection mode.

Setting of [F11] Display resolution completed.



: It may not be possible to change the resolution depending on the unit of pressure selected..

The units that allow display resolution to be selected are MPa, kPa, kgf/cm

2

, psi and inHg.

(The units kgf/cm

2

, bar, psi and inHg can only be set when using a product with unit conversion function.)

[F 0] Unit selection function on page 24.

Setting of display resolution

Press the

or

button to select display resolution.

«
...
32
33
34
35
36
...
»

Содержание ZK2-ZSV-A Series


























































Отзывы:

Нет отзывов

Похожие инструкции для ZK2-ZSV-A Series

Бренд: Magnetrol Страницы: 12

Бренд: Magnetrol Страницы: 24

Бренд: D-Link Страницы: 36

Бренд: ORiNG Страницы: 2

Бренд: Lantech Страницы: 118

Бренд: Ribimex Страницы: 15

Edison Cooper Power Series

Бренд: Eaton Страницы: 12

Бренд: GE Страницы: 50

Бренд: Digitronic Страницы: 24

Бренд: BluStream Страницы: 4

Бренд: B&B Electronics Страницы: 2

Бренд: Link Страницы: 35

Бренд: Conceptronic Страницы: 28

GSM7352S - ProSafe Switch - Stackable

Бренд: NETGEAR Страницы: 628

Master View CS-172

Бренд: ATEN Страницы: 1

Бренд: Wyrestorm Страницы: 4

Бренд: GenerLink Страницы: 16

Alduti-Rupter Switches Outdoor Distribution

Бренд: S&C Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды