background image

1. Before You Begin

Your vehicle’s STOCK program

Your vehicle’s ECM must contain the manufacturer’s STOCK factory program.  If you have used a 
programmer from another aftermarket company you must use their product to return your ECM back 
to STOCK condition before proceeding. If you have a performance-enhancing device installed, it must 
be removed.

Service Centers

If you need to return your vehicle to a service center, restore the vehicle ECM to its STOCK program. 
The service center might reprogram your vehicle with an updated, STOCK, software ECM reflash 
without  your knowledge.   If your vehicle has not been returned to its STOCK program prior to a 
service visit and the ECM is reflashed, the Smarty Micro Tuner will no longer be able to program 
your vehicle.  Such failure is not covered by the MADS warranty.
Under no circumstances will we refund, repair, or warranty units that are sent in that are locked.

Locking and Unlocking Smarty.

Once Smarty is used on a vehicle, it is VIN # LOCKED to that vehicle AND to that ECM. Smarty can 
be used only on that vehicle to update ECM software and ABS (speedometer) changes.   In order to 
unlock Smarty, you must use Smarty to return the ECM to the STOCK software, otherwise, Smarty 
will remain locked.  Only Smarty can unlock itself.  Follow the instructions in this Manual to return 
your vehicle to STOCK software.  Once unlocked, Smarty may be used on a different vehicle.  While 
Smarty is VIN# Locked, it can still be used to read and clear Diagnostic Trouble Codes (DTCs) on a 
vehicle and ECM that it is NOT locked to. 

Vehicle preparation

Before   connecting   the   Smarty   Micro   Tuner   to   your   vehicle,   make   sure   that   all   power-draining 
accessories are turned off: Radio, headlights, lights, cell phones, etc.   All those devices need to be 
turned off. Please apply the parking brake before you begin a download.
As the Smarty Micro Tuner needs full battery voltage to program, ensure your vehicle battery is fully 
charged and NOT connected to a battery charger.  
Do not disturb or remove the connection cable during the updating operation.

Smarty preparation

During the first use, Smarty reads the identification parameters of your vehicle. After the first use, 
Smarty can be used only with your vehicle.
Returning the ECM to STOCK software restores Smarty into the original, unlocked condition.

2. Smarty Overview

Keyboard operation

Smarty’s keyboard is composed of 12 keys:

Numerical keys from 0 to 9, used to select menu options and enter numerical values

Right arrow key, used to confirm the selected operation

Left arrow key, used to go one step back in the operation flow

Connectors

Two connectors are available in Smarty’s upper edge:

USB Connector: Used for connecting Smarty to a personal computer for updates.   The update 
softwares can be downloaded from MADS internet site (www.madselectronics.com).

Page 5 of 16

Содержание SSR S06-SSR

















Отзывы: