background image

10. Appendix A: Error messages description

This section contains all the possible error messages shown by Smarty:

Error message

Cause

Solution

CAN ERROR #

A problem in the CAN Bus 
communication

Check connection cable or contact 
MADS if the problem persists

CCD ERROR #

The communication with 
ABS unit doesn’t work

Check connection cable or check ABS 
unit

COMM. TIME OUT

The ECM of the vehicle 
doesn’t answer to Smarty 

Turn the ignition key on (DO NOT 
START ENGINE) or Check the 
connection cable

ECM Changed

The ECM unit of the vehicle 
has been changed

Restore the original ECM back to 
STOCK before changing ECM

Empty Memory,
Please Update

The last Update operation 
(through USB port) has been 
unsuccessfully completed.
Smarty memory has been 
corrupted.

Repeat the Update operation.
The data files are available on the 
MADS internet site.

INTERNAL ERROR #

Smarty internal malfunction

Call MADS assistance

Memory Error

A malfunction in the 
Smarty’s memory

Call MADS assistance

Memory Written
Wrong Data File

The update file transmitted 
to Smarty through USB port 
is corrupted

Download again the update file from 
MADS internet site and update Smarty 
with the correct file

PROGRAM ABORTED

The ECM update function 
has been interrupted

Restore the ECM to STOCK with the 
recovery procedure.

S/N Verify Error

The serial number of your 
vehicle has not been verified

Check connection cable

SW Version doesn’t
Match S/N

The ECM software version 
doesn’t match with the serial 
number

Please contact MADS or the seller.

UNKNOWN SOFTWARE Your vehicle contains a 

software version unknown to 
Smarty

Please contact MADS or the seller.

VIN# Locked

Smarty has been connected 
to a different vehicle

Restore the original vehicle back to 
STOCK before connecting Smarty to a 
new vehicle

WRONG CAN BUS

The connection between 
Smarty and the ECM is not 
correct

Please contact MADS or the seller.

WRONG COMMUNIC.

The communication between 
Smarty and the ECM unit is 
disturbed

Check the connection cable or the 
battery charge level

WRONG VIN#

The serial number of your 
vehicle is not valid

Wait 30 seconds with the ignition key 
on and try again

Page 15 of 16

Содержание SSR S06-SSR

















Отзывы: