background image

CAUTION

This  MADS  product   is   intended   for   use   on   unmodified   stock   engines.     Remove  any   performance 
enhancing electronic devices and make sure the ECM has been returned to STOCK if you have used 
another manufacturer’s programmer before the Smarty Micro Tuner.

The use of this product to change the performance characteristics of your vehicle could invalidate the 
warranty   provided   by   the   vehicle   manufacturer.     Consult   your   vehicle   warranty   before   using   the 
product on your vehicle.

NEVER CONNECT BOTH THE SMARTY CONNECTORS AT THE SAME TIME!   
This could damage Smarty and the computer USB port. 

NEVER UNPLUG SMARTY WHILE IT IS UPDATING YOUR ECM.
Smarty can recover without pulling fuses, or disconnecting batteries, BUT do not intentionally create 
this situation.   When Smarty is DONE with ECM updates, ABS changes, or clearing DTC codes, it 
may be unplugged, even if Smarty does not display the typical “Unplug Smarty and Turn Key OFF” 
screen.

It   is   recommended   that   you   do   not   store   your   Smarty   Micro   Tuner   in   your   vehicle   if   ambient 
temperatures in your area fall below 32°F.   Excessively low temperatures can cause malfunction or 
damage to Smarty Micro Tuner that is not covered by the MADS warranty.

In  the case of ECM replacement,  restore the ECM back to the STOCK software  before the ECM 
replacement.  Smarty works only with one vehicle and one ECM at a time while it is VIN Locked. 
Under no circumstances we will refund, repair, or warranty units that are send in and result VIN # 
locked.

RESTORE ECM TO STOCK SOFTWARE BEFORE ANY SERVICE ASSISTANCE.
If you need to return your vehicle to a service center, restore the vehicle ECM to its STOCK program 
by following the instruction in this manual.  The service center might reprogram your vehicle with an 
updated,   STOCK,   software   ECM   reflash  without  your   knowledge.     If   your   vehicle   has   not   been 
returned to its STOCK program prior to a service visit and the ECM is reflashed, the Smarty Micro 
Tuner will no longer be able to program  your vehicle.   Such failure is not covered  by the  MADS 
warranty.   Under no circumstances will we refund, repair, or warranty units that are sent in that are 
locked.

Page 3 of 16

Содержание SSR S06-SSR

















Отзывы: