Smartgen HGM9510 Скачать руководство пользователя страница 39

Страница: 39 / 65

HGM9510 GENSET PARALLEL UNIT

HGM9510 Genset Parallel Unit ISSUE 2013-08-06 Version 1.1 Page 39 of 65

threshold.

Oil Pre-supply Output

Action from “crank on” to “safety on”.

Generator Excite

Output in start period. If there is no generator frequency
during hi-speed running, output for 2 seconds again.

Pre-Lubricate

Actions in period of pre-heating to safety run.

Remote Control Output

This port is controlled by communication (PC).

Reserved

Close Gen Output

Control generator to take load.

Open Gen Output

Control generator to off load.

Reserved

Start Relay

Fuel Relay

Action when genset is starting and disconnect when stop
is completed.

Idle Control

Used for engine which has idles. Close before starting and
open in warming up delay; Close during stopping idle
mode and open when stop is completed.

Speed Raise Relay

Action in warming up delay.

Speed Drop Relay

Action

between the period from “stop idle” to “failed to

stop”.

Energize to Stop

Used for engines with ETS electromagnet. Close when
stop idle is over and open when pre-

set “ETS delay” is

over.

Speed Drop Pulse

Active 0.1s when controller enter into stop idle, used for
control part of ECU dropping to idle speed.

ECU Stop

Used for ECU engine and control its stop.

ECU Power Supply

Used for ECU engine and control its power.

Speed Raise Pulse

Active 0.1s when controller enter into warming up delay;
used for control part of ECU raising to normal speed.

Crank Success

Close when detects a successful start signal.

Generator OK

Action when generator is normal.

Generator

Load

Available

Action in period of generator ok to hi-speed cooling.

Reserved

Synchronizing

Action when controller is synchronizing.

Common Alarm

Action when genset common warning, common
shutdown, common trips alarm.

Common Trip and Stop

Action when common trip and stop alarm.

Common Shutdown

Action when common shutdown alarm.

Common Trip

Action when common trips alarm.

Common Warn

Action when common warning alarm.

Reserved

Battery Over Voltage

Action when

battery’s over voltage warning alarm.

Battery Under Voltage

Action when

battery’s low voltage warning alarm.

Charge

Alternator

Failure

Action when charge fail warning alarms.

Содержание HGM9510


































































Результаты поиска

Содержание HGM9510

Отзывы:

Похожие инструкции для HGM9510

Бренды по названию

Популярные бренды

Smartgen HGM9510, Руководство пользователя

Результаты поиска

Содержание HGM9510

Отзывы:

Похожие инструкции для HGM9510

Бренды по названию

Популярные бренды