Smartgen HGM9510 Скачать руководство пользователя страница 11

Страница: 11 / 65

HGM9510 GENSET PARALLEL UNIT

HGM9510 Genset Parallel Unit ISSUE 2013-08-06 Version 1.1 Page 11 of 65

Mute/Reset
Alarm

Alarming sound off; If trip alarm occurs, pressing the button
at least 3 seconds can reset this alarm.

Close breaker in manual mode.

Open

Open breaker in manual mode.

Up/Increase

1) Screen scroll;
2) Up cursor and increase value in setting menu.

Down/Decrease

1) Screen scroll;
2) Down cursor and decrease value in setting menu.

Left

1) Screen scroll;
2) Left move cursor in setting menu.

Right

1) Screen scroll;
2) Right move cursor in setting menu.

Set/Confirm

Select viewing area.

Exit

1)Return to main menu;
2) Return to previous menu in setting menu.

NOTE

: Press

and

simultaneously in manual mode will force generator to

crank. Successful start will not be judged according to crank disconnect conditions, operator will

have to crank the starter motor manually; when operator decides that the engine has fired, he/she

should release the button and start output will be deactivated, safety on delay will be initiated.

WARNING:

Default password is 00318, user can change it in case of others change the

advanced parameters setting. Please clearly remember the password after changing. If you forget

it, please contact Smartgen services and send all information in the controller page of “

ABOUT

” to

us.

5.3 LCD DISPLAY

5.3.1 MAIN DISPLAY

Main screen show pages; use

to scroll the pages and

to scroll the screen.

★

Main Screen

, including as below,

Gen: voltage, frequency, current, active power, reactive power

Bus: voltage, frequency

Engine: speed, temperature, oil pressure

Some status

★

Status

, including as below,

Содержание HGM9510


































































Результаты поиска

Содержание HGM9510

Отзывы:

Похожие инструкции для HGM9510

Бренды по названию

Популярные бренды

Smartgen HGM9510, Руководство пользователя

Результаты поиска

Содержание HGM9510

Отзывы:

Похожие инструкции для HGM9510

Бренды по названию

Популярные бренды