Smartgen HGM9510 Скачать руководство пользователя страница 46

Страница: 46 / 65

HGM9510 GENSET PARALLEL UNIT

HGM9510 Genset Parallel Unit ISSUE 2013-08-06 Version 1.1 Page 46 of 65

No.

Description

Remark

Oil Level Sensor

0 Not used
1 Custom Res Curve
2 Custom 4-20mA curve
3 SGD
4 SGH
5~15 Reserved

Defined resistance’s range is
0~6KΩ, default is SGH sensor.

NOTE:

User should make special declare when order controller if your genset equip with

sensor of 4~20mA.

8.5 CONDITIONS OF CRANK DINSCONNECT SELECTION

No.

Setting description

Gen frequency

Speed sensor

Speed Gen frequency

Oil pressure

Oil pr Gen frequency

Oil pr Speed sensor

Oil pr Speed Gen frequency

NOTE:

a. There are 3 conditions to make starter disconnected with engine, that is, speed sensor,

generator frequency and engine oil pressure. They all can be used separately. We

recommend that engine oil pressure should be using with speed sensor and generator

frequency together, in order to make the starter motor is separated with engine immediately

and can check crank disconnect exactly.

b. Speed sensor is the magnetic equipment which be installed in starter for detecting flywheel

teeth.

c. When set as speed sensor, must ensure that the number of flywheel teeth is as same as

setting, otherwise, “over speed stop” or “under speed stop” may be caused.

If genset without speed sensor, please don’t select corresponding items, otherwise, “start fail”

or “loss speed signal” maybe caused.

If genset without oil pressure sensor, please don’t select corresponding items.

f. If not select generator frequency in crank disconnect setting, controller will not collect and

display the relative power quantity (can be used in water pump set); if not select speed sensor

in crank disconnect setting, the rotating speed displayed in controller is calculated by

generator frequency and number of poles.

Содержание HGM9510


































































Результаты поиска

Содержание HGM9510

Отзывы:

Похожие инструкции для HGM9510

Бренды по названию

Популярные бренды

Smartgen HGM9510, Руководство пользователя

Результаты поиска

Содержание HGM9510

Отзывы:

Похожие инструкции для HGM9510

Бренды по названию

Популярные бренды