Slycma ARIANE 3.1 Скачать руководство пользователя

Страница: 31 / 34

Ref : 26702 31 07/01/15

To return to the parameter list, press

EST

S AND ADJUST

Reprogram card parameters following paragraph with title

« On-site replacement of

an ARIANE card » page 21

Erase memory following indications page 37 and check if

faulty operation appears again.

Check U1. and U2. Voltage parameters and decrease them.

Check winding, wiring (court-circuit)

Check U1. and U2. Voltage parameters and decrease them.

Check winding, wiring (court-circuit)

Check U1. and U2. Voltage parameters and decrease them.

See problems met : "the door doesn’t see the encoder

anymore”

Check the 3 windings balance.

Check the m

otor’s wiring.

Ramener la tension secteur à 220 V thanks to a

transformateur

Increase deceleration times

Reduce mains power voltage to 220 V à l'aide d'un

transformer

Erase memory : faults stor

ed, following § instruction and

check if fault appears again

Select asynchr

onous motor in parameters

Reload param

eters tables INxx

Corresponding to the door type controlled

(see § Notice: configuration following door type)

CAUSES

Memory

Fault

Connector disconnected in the unit

Ventilation fault or parametering fault

otor fault

Parametering fault

otor fault

Parametering fault

Faulty encoder

aulty m

otor

Faulty motor wiring

Mains power voltage superior to 270V

For heavy doors equipped with brushless motor

If deceleration time is too short

Mains power voltage inferior to 155 v

Hard and soft incompatibles

If brushless motor selected in parameters and

asynchronous motor installed.

Parameters do not corres

pond to the type of door

used

OBLEMS MET

Err1 m

ory fault

Err2 (Mute power card)

Err3 (Excessive

temperature)

Err4 (Overcurrent)

Err5 (Overload)

Err6 (Motor or encoder fault)

Err7 (Mains power supply over-voltage)

Err8 ( Mains power supply undervoltage)

Err9 ( Logical and power card incompatibles)

Err10 (Hall effect sensor fault)

*** Com

ent : generally speaking, when a

door is operating abnormally , check, first, if

the parameters loaded suit the door type

controlled.

Содержание ARIANE 3.1



































Результаты поиска

Содержание ARIANE 3.1

Отзывы:

Похожие инструкции для ARIANE 3.1

Бренды по названию

Популярные бренды

Slycma ARIANE 3.1, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание ARIANE 3.1

Отзывы:

Похожие инструкции для ARIANE 3.1

Бренды по названию

Популярные бренды