Slycma ARIANE 3.1 Скачать руководство пользователя

Страница: 29 / 34

Ref : 26702 29 07/01/15

DETAILS ABOUT FAILURES TO OPERATE

The card indicates only the faults which it can

detect via the mains power, encoder and motor

links.

Err0

End of fault

Normal operation restored.

Err1

Memory fault

Operates in fail soft mode.

Reprogram all the parameters and do the travel learning again and

save the parameters.

Err2

Blank power card

Blocks the motor commands.

Check the shieldings, internal foreign body, link braid between

cards, etc.

Err3

High temperature

Wait for the temperature to decrease by 5°C. The motor can no

longer be commanded during this time interval.

Improve the ventilation of the motor and card, lower the voltages

U1, etc.

Err4

Motor overcurrent detected

Stops the motor for 0.5 seconds. If the fault occurs more than five

times in less than a minute, the message remains displayed and the

motor can no longer be commanded for 1 minute.

Check the motor, wirings (short-circuit), voltages U1.

Err5

Overload detected

Reduces the value of the voltage applied to the motor to limit the

overload.

Check the motor, reduce the voltages U1, ventilate better.

Err6

Counting or driving fault.

Operation goes into fail soft mode.

Check the encoder, motor, increase the voltages U1.

Err7

Mains overvoltage fault (higher than 270V)

Mains voltage too high or voltage generated due to a slowing down

of a heavy door with a Brushless motor.

Does not block the motor commands, but could destroy the

power supply.

Change the mains power supply to reduce the voltage or lower the

deceleration slopes.

Содержание ARIANE 3.1



































Результаты поиска

Содержание ARIANE 3.1

Отзывы:

Похожие инструкции для ARIANE 3.1

Бренды по названию

Популярные бренды

Slycma ARIANE 3.1, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание ARIANE 3.1

Отзывы:

Похожие инструкции для ARIANE 3.1

Бренды по названию

Популярные бренды