SlimLine Eco 17L, Техническое руководство

Страница: 11 / 36

MAINTENANCE
Page 11
ROUTINE CHECKS
Regularly the user should perform a basic check to verify if
the water softener is functioning correctly, on the basis of
the following control points:
1.
Check settings of electronic control panel.
2. Measure water hardness before/after water softener.
3. Check drain line from control valve; there shouldn’t be
any water flow (unless water softener is in
regeneration).
4. Check drain line from cabinet overflow; there shouldn’t
be any water flow.
5. Check water softener and surrounding area; there
shouldn’t be any water leakages.
BYPASSING THE WATER SOFTENER
Occasionally it may be necessary to put the water softener
hydraulically in bypass, i.e. to isolate it from the water
distribution system; f.e.:

in case of an urgent technical problem;

when it is not necessary to supply treated water to the
house/application (refill swimming pool, irrigation,...).
WITH FACTORY BYPASS (optional)
Picture 8.a
SERVICE POSITION

= inlet valve to water softener is OPEN

= outlet valve from water softener is OPEN
Picture 8.b
BYPASS POSITION

= inlet valve to water softener is CLOSED

= outlet valve from water softener is CLOSED
Picture 8.c
MAINTENANCE POSITION

= inlet valve to water softener is OPEN

= outlet valve from water softener is CLOSED
WITH 3-VALVE BYPASS SYSTEM (not included)
Picture 9.a
SERVICE POSITION

= bypass valve is CLOSED

= inlet valve to water softener is OPEN

= outlet valve from water softener is OPEN
Picture 9.b
BYPASS POSITION

= bypass valve is OPEN

= inlet valve to water softener is CLOSED

= outlet valve from water softener is CLOSED
Picture 9.c
MAINTENANCE POSITION

= bypass valve is OPEN

= inlet valve to water softener is OPEN

= outlet valve from water softener is CLOSED
WATER CONDITIONER SALT
Picture 10
The water softener needs 'brine' for its periodic
regenerations. This brine solution is made from water, that
is automatically dosed in the brine cabinet by the control
valve, and water conditioner salt. The user should make sure
that the brine cabinet is always kept full of water conditioner
salt. Therefore he should periodically check the salt level
inside the brine cabinet and refill it if necessary. The salt lid
can be removed completely to facilitate refilling.
Ideally the level of water conditioner salt inside the brine
cabinet is kept between 1/3 and 2/3. A lower level of water
conditioner salt can cause insufficient brine saturation,
resulting in a loss of softening capacity. A higher level of
water conditioner salt can cause salt bridging (hard crust or
salt bridges in the brine cabinet). When you suspect salt
bridging:

carefully pound on the outside of the brine cabinet to
break loose the salt bridges;

using a broom (or like blunt tool) carefully push the salt
to break it apart;

pour warm water over the top of the salt to dissolve it.
BRINE CABINET
To retain the appearance of the water softener, simply wipe
it with a damp cloth or clean it with a mild soap solution;
never use abrasive cleaners, ammonia or solvents.
RESIN CLEANER
Other contaminants (f.e. iron) present in the feed water can
cause the resin bed to foul up, resulting in a loss of softening
capacity. An approved resin cleaner can be used periodically
to thoroughly clean the resin bed.
SANITIZING THE WATER SOFTENER
This water softener is manufactured from premium quality
material and assembled in safe conditions to assure it is
clean and sanitary. If installed and serviced correctly, this
water softener will not infect or contaminate your water
supply. However, as in any 'device' plumbed-in in your water
distribution system, a proliferation of bacteria is possible,
especially in case of 'stagnant water'. Therefore this water
softener is equipped with a 'days override' feature, that will
automatically rinse the resin bed periodically, even in case of
low or absence of water usage.
If the power supply to the water softener is disconnected for
a longer period of time, we recommend, when the power
supply is re-established, to manually initiate a complete
regeneration.