SkyWave IDP 800 Series Скачать руководство пользователя страница 57

Страница: 57 / 102

IDP 800 Terminal Series - Hardware Guide

Figure 30 Battery Cover

Apply

firm hand pressure

around the outside of the battery cover before tightening

the screws (Figure 31).

Figure 31 Apply Pressure around the Battery Cover

Tighten the screws (four places) with a #2 Phillips torque screwdriver. Torque
screws to

0.7 N-m (6 in-lb)

. The terminal automatically powers on once the batteries

are inserted. Once the terminal has power, the LED emits a few short flashes.

Note:

The battery cover should lay flat on the terminal base when properly
assembled and all four screws must be tightened.

CAUTION

Do not over torque the battery
cover screws as this voids
the warranty.

4.5.2 Recharge the Batteries

Rechargeable batteries should be fully charged (4 hours) prior to initial use. The batteries
can be recharged by connecting either an external power cable (ST100165) or an IDP 800
AC power adapter cable (ST100164).

Line up the

straight edges

Содержание IDP 800 Series







































































































Результаты поиска

Содержание IDP 800 Series

Отзывы:

SkyWave IDP 800 Series, Руководство по оборудованию, Страница: 57 / 102

Результаты поиска

Содержание IDP 800 Series

Отзывы: