SKS Sweden Bonfiglioli Vectron Agile Скачать руководство пользователя страница 31

Страница: 31 / 104

CANopen Agile

06/2010

Protocol

8.10

OS Synchronization

The operating System (OS) of the frequency inverter can be synchronized to the PLC or other devic-

es. The synchronization of the OS enhances the performance of the complete plant. Synchronization

is used to eliminate phase deviations of the CPUs between master and slave devices, so that calcu-

lations are done at the same time. Note, that only small deviations of the CPU clock frequencies

between devices (i.e. different CPU Quartz cock frequenices) of ± 1 ‰ can be compensated.

Synchronization via CANopen:
When using CANopen without Systembus, the synchronization can be switched on and off. Synchro-

nization can be only done with CANopen SYNC telegrams.

Synchronization via Systembus:

When using CANopen simultaneously with Systembus, the synchronization can be set to either CA-

Nopen, Systembus or it can be switched off. Synchronization can be done with Systembus SYNC

telegrams or Systembus RxPDO telegrams.
Note: When synchronizing the OS via CANopen, the master has to support the synchronization me-

chanisms of CANopen.

OS_SyncSource

1452

Operation Mode

Function

0 - Auto

The synchronization source is selected automatically by the inverter.

1 - CANopen

The OS is synchronized via CANopen. Factory setting.

2 - Systembus

The OS is synchronized via Systembus.

99 - Off

The OS is not synchronized with other devices.

Operation mode Auto: The selection is done via this decision table:

CANopen active

Systembus active

Synchronization

Yes



Synchronization via CANopen

Yes



Synchronization via Systembus



No Synchronization activated.

The CANopen "active status for synchronization" is recognized by the parameter setting 387

CAN

Node Number

>0 and a running synchronous PDO.

The Systembus "active status for synchronization" is recognized by the parameter setting 900

System-

bus Node ID

>0. Also parameter 1180

Synchronization

has to be set to SYNC or an RxPDO.

Protocol



1180 Operation Mode (Synchronization)

Operation Mode

1180

Function

0 - Aus

No evaluation of SYNC-Telegrams.

1 - RxPDO1

RxPDO1 used as SYNC-Telegram.

2 - RxPDO2

RxPDO2 used as SYNC-Telegram.

3 - RxPDO3

RxPDO3 used as SYNC-Telegram.

10 - SYNC

SYNC used as SYNC-Telegram.

With Parameter

Operation Mode

1180 the telegram for the synchronisation on the Systembus is de-

termined.

The selected telegram is used

−

for the synchronisation of the operating system (if Parameter

OS_SyncSource

1452 is set to "Sys-

tembus") and

−

for the processing of the synchronous PDOs on the Systembus (if set in Parameters 930, 932, 934,
936-938).



1451 CANopen OS Synctime

Parameter

CANopen OS Synctime

1451 can be used to shift the point of the synchronization inside

of 1 ms. When you experience noises from a motor, shifting the

CANopen OS Synctime can result in a

better behavior.

OS SyncSource Act

1453 shows the active Synchronization source.

Parameter

Setting

No.

Description

Min.

Max.

Fact. sett.

1451 CANopen OS Synctime

700 us

900 us

800 us

For the CANopen Synchronisation pay also attention to Objects

0x1005/0 COB-ID SYNC Message

0x1006/0 Communication Cycle Period

and

0x1007/0 Synchronous Window Length

For the VPlus Scope Function the following sources are available for diagnosis:

Operation Mode

Function

731 - B: Sync. OS <-> Sysbus Ok

1 = Synchronization OS to Systembus OK,

0 = Synchronization OS to Systembus not OK

852-

SysBus SYNC time [us]

Shows the Synchronization cycle. Should show the

set SYNC time or TxPDO time of the sending master.

853

SysBus SYNC position 1ms Task [us]

Shows the Synchronization time inside 1 ms. Should

remain constant with small fluctuations.

854- B: Sync. OS <-> CANopen Ok

1 = Synchronization OS to CANopen OK,

0 = Synchronization OS to CANopen not OK

848-

CANopen SYNC time [us]

Shows the Synchronization cycle. Should show the

set SYNC time of object

0x1006

849- CANopen SYNC position 1 ms Task [us] Shows the Synchronization time inside 1 ms. Should

remain constant with small fluctuations.

Содержание Bonfiglioli Vectron Agile









































































































Результаты поиска

Содержание Bonfiglioli Vectron Agile

Отзывы:

Похожие инструкции для Bonfiglioli Vectron Agile

Бренды по названию

Популярные бренды

SKS Sweden Bonfiglioli Vectron Agile, Руководство по связи

Результаты поиска

Содержание Bonfiglioli Vectron Agile

Отзывы:

Похожие инструкции для Bonfiglioli Vectron Agile

Бренды по названию

Популярные бренды