Skil 3700, Инструкция по эксплуатации и безопасности

Страница: 5 / 112

5.
Basic Operation and Set Up
Table saws are intended to cut wood, wood like or
plastic materials. Do not cut metal with table saws.
Plastic and composition (like hardboard) materials may
be cut on your saw. However, since these are usually quite
hard and slippery, the anti-kickback pawls may not stop a
kickback. Therefore, be especially attentive to following
proper set-up and cutting procedures for ripping. Do not
stand, or permit anyone else to stand, in line with a potential
kickback.
Unplug saw before making adjustments, repairs or
storing. Accidental start-ups can cause serious personal
injury.
Wear eye, ear and dust protection. Dust and particles
from cutting should not be inhaled. Eye protection can shield
your eyes if small pieces of wood or other objects are thrown
back during operation. Power tools are loud in operation,
protect your hearing with earplugs or muffs.
Do not wear such items as loose fitting gloves, loose
clothing, necktie, or jewelry. Tie back long hair and roll
long sleeves above elbows. Loose clothing or jewelry can
be caught in rotating parts and you may be dragged into the
cutting element of the power tool.
Use the table saw in a well-lit area and on a level
surface, clean and smooth enough to reduce the risk of
trips and falls. Cluttered work areas are accidents waiting
to happen.
Make sure the floor is clean and non-slippery or non-
skid where the table saw is set up. Wear non-slip
footwear. If you cannot control your motion, you cannot
control the work.
Never turn the saw “ON” before clearing the table of all
tools, wood scraps, etc., except the workpiece and related
feed or support devices for the operation planned.
To avoid tipping your table saw in operation, BOLT it
securely to a stand or workbench. Long workpieces
need extra support on the outfeed side such as an
auxiliary support or roller stand. Long and heavy pieces
may cause the table saw to tip over if not supported properly.
Don’t try to cut large sheets that you cannot guide with
the fence or miter gauge. If you cannot see the tabletop
under the workpiece, the workpiece is too big for safe cutting
with the table saw.
Turn the table saw “OFF” and let the spinning blade
stop before attempting to remove cutoff or workpiece
from table. You may inadvertently contact the coasting
blade.
Use common sense – if your set up doesn’t feel right or
is not complete – Don’t attempt the cut! Complete the set
up using clamps, feather boards, push sticks, fence, miter
gauge, outfeed support, side support or whatever it takes to
keep the workpiece moving through the blade cleanly,
smoothly and without making contact with you.
Stop operating immediately if any part of your saw is
missing, malfunctioning, has been damaged or broken
such as the motor switch, or other operating control, a
safety device or the power cord. Repair or replace the
particular part before operating the table saw again.
Causes and Operator Prevention of Kickback
with a Table Saw:
Kickbacks are caused by operator inattention and misuse of
the table saw (i.e. binding the blade, lack of guard, splitter,
kickback pawls or use of miter gauge with rip fence).
Table Saw Specific Safety Rules
Tool Care
DO NOT ALTER OR MISUSE TOOL
These tools are precision built. Any alteration or modification not
specified is misuse and may result in dangerous conditions.
AVOID GASEOUS AREAS
Do not operate electric tools in gaseous or explosive atmo-
spheres. Motors in these tools normally spark, and may re-
sult in a dangerous condition.
MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for better and safer performance.
Follow instructions for lubricating and changing accessories.
Inspect tool cords periodically and if damaged, have repaired
by authorized service facility. Inspect extension cords
periodically and replace if damaged. Keep handles dry, clean
and free from oil and grease.
CONNECTING THE TOOL
Before connecting the tool to a power source (receptacle,
outlet, etc.), be sure voltage supplied is the same as that
specified on the nameplate of the tool. A power source with
voltage greater than that specified for the tool can result in
serious injury to the user — as well as damage to the tool.
If in doubt, DO NOT PLUG IN THE TOOL. Using a power
source with voltage less than the nameplate rating is harmful
to the motor.
Use only Skil replacement parts. Any others may create a
hazard.
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other masonry
products, and
• Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
WARNING
!