manualshive.com logo in svg

SKF LAGD 1000 series, Инструкция по эксплуатации

Поделиться
Скачать
SKF LAGD 1000 series Скачать руководство пользователя страница 21

21

SKF LAGD 1000

4.1.1  Operation via push buttons

Push button

Operating possibilities

 

 

• Operating the button during PAUSE, will initiate an  

 

   intermediate lubrication cycle

 

• Fault messages are acknowledged and cleared

 

 

• Automatically activates the display in display mode

 

• Calls up the next parameter in programming mode

 

• Increases the displayed value by 1

 

 

• Automatically activates the display in display mode

 

• Calls up the last parameter in programming mode

 

• Decreases the displayed value by 1

 

 

• Change between programming and display mode

 

• Conirm entered values

4.1.2  Three digit LED display

During normal operation, the display is off. It is activated by briely operating one  
of the two push buttons. It is used for displaying current values and preset parameters.  
In addition, the display is used for operator prompting during programming of  
operating parameters.

Display

Function

Description

 

t 

= TIMER

PA 

= PAUZE

The control unit
operates as a time
controlled contact
maker (TIMER) and is  
in the PAUSE mode

• Part of lubrication cycle 
   Entered and displayed  
   value in hours

 

c

 = COUNTER

PA 

= PAUZE

The control unit
operates as a contact
counter (COUNTER) and
is in the PAUSE mode

• Part of lubrication cycle
• The device counts the  
   pulses from an external 
   contact maker and 
   compares them with the 
   preset values

 

t 

= TIMER

CO 

= CONTACT

The control unit
operates as a
timecontrolled contact
maker (TIMER) and is
in the pump running
mode (CONTACT)

• CONTACT = time during 
   which the pump delivers 
• Entered and displayed 
   value in minutes

 

c 

= COUNTER

CO

 = CONTACT

DO NOT USE

Содержание LAGD 1000 series






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды