Sime Planet Super 4 F.S., Инструкция по установке и обслуживанию

Страница: 56 / 76

14
4.1 ELECTRONIC PANEL
Made in accordance with the Low Voltage
EEC directive 73/23, supplied with 230
Volt; via a transformer it sends 24 Volt to
the following components: gas valve, safety
stat, C.H. and D.H.W. sensors, external
temperature sensor (optional), modulator,
water pressure transducer, smoke stat,
room stat or “Logica Remote Control”.
An automatic and continuous modulating
system allows the boiler to adjust the
p o w e r t o t h e v a r i o u s p l a n t o r u s e r
demands. The electronic components are
guarant eed t o work in a t emperatur e
range between 0 and +60 °C.
4.1.1 Functioning faults
The leds that show an irregular and/or
incorrect functioning of the apparatus are
shown in fig. 21.
4.1.2 Devices
The electronic panel has the following
devices:
– Trimmer “POT. RISC.” (10 fig. 22)
It regulates the maximum value of heat-
ing power. To increase the value turn the
trimmer in a clockwise direction and to
decrease it turn the trimmer in an anti-
clockwise direction.
– Trimmer “POT. ACC.” (6 fig. 22)
Trimmer for the changing of the ignition
pressure level (STEP) of the gas valve.
According to the type of gas for which
the boiler is predisposed, the trimmer
must be regulated so as to provide the
burner with a pressure of around 3
mbar for methane gas or 7 mbar for
but ane gas (G30) and pr opane gas
(G31). To increase the pressure turn the
trimmer in a clockwise direction, to
decrease it turn the trimmer in an anti-
clockwise direction.
The level of pressure of slow ignition is
able to be set during the first 5 seconds
from the starting of the burner.
Af ter having established the level of
pressure at ignition (STEP) according to
the type of gas, check that the heating
gas pressure is still on the value set
beforehand.
– Connector “MET-GPL” (7 fig. 22)
With the connector disconnected, the
boiler is ready to function with METHANE;
with the connector connected with LPG.
– Connector “ANN. RIT.” (5 fig. 22)
The electronic panel is programmed, in
heating phase, with a technical pause by
the burner of around 90 seconds, both
at the beginning when the plant is cold
and in the subsequent startings.
This is so to avoid ignitions and switching
off with very short intervals, that may in
particular be found in plants with high
losses.
At every restarting, following the period
of slow ignition, the boiler will position
itself for around 1 minute to the mini-
m u m m o d u l a t i n g p r e s s u r e t o t h e n
return to the set value of heating pres-
sure. With the insertion of the bridge
both the technical pause programmed
and the period of functioning at minimum
pressure in the ignition phase will be
eliminated.
I n s u c h a c a s e , t h e t i m e t h a t r u n s
between the switching off and the next
ignition will be in function of a variance of
5°C, as shown by the C.H. sensor (SM).
– DIP SWITCH (13 fig. 22)
Ensure that the riders are inserted in
the position shown in order for the boiler
to work:
4 CHARACTERISTICS
3.10.3 Gradient of the characteristic
heating curve
The gradient of the characteristic heating
curve is imposed on the current value “15”
of Logica. Increasing the gradient as shown
in the drawing of fig. 20, the C.H. flow tem-
perature increases in correspondence to
the outside temperature.
EXAMPLE: Choosing a gradient of 15 with
an outside temperature of –10°C we shall
have a C.H. flow temperature of 60°C.
3.11 EXTERNAL TEMPERATURE
SENSOR
The "Logica Remote Control" can be con-
nected to an external temperature sensor
available an optional extra (code 8094100).
This configuration ensures and maintains
the required temperature constant in the
room. The ambient temperature is, in fact,
indicted and evaluated as the calculated
mean of the value measured inside and out-
side the dwelling.
For installation, follow the assembly instruc-
tions inserted in the package.
Fig. 20