Sime MIA-30, Инструкция для пользователя, по установке и обслуживанию

Страница: 39 / 72

39
7.5 Display of operating data and counters
Access the operating data
"In"
and the counters
"CO"
as fol-
lows:
– from the operating screen in the mode enabled at that mo-
ment (WINTER n or SUMMER l )
– go into "INFO" by pressing the buttons > and < at the same
time
for more than 3 seconds until
"In"
appears alternating
with
"0.0"
(information number) and
"25"
(eg. value)
From this point, the technician has 2 options:
– scroll through the list of
"info"
and
"counters"
by pressing
the button > . This way, scrolling will be in sequence
– display the “activated alarms” (no more than 10) by pressing
the button < . Once in this section, proceed with button > or
< .
When all the values have been displayed, exit the menu by
pressing and holding down the button o for approximately 5
seconds until the initial screen is displayed.
TABLE OF INFORMATION DISPLAYED
Type No. Description Range U/M Step
In 0.0 SW version
In 0.1 External sensor (SE) - 9 .. 99 °C 1
In 0.2 Delivery sensor tem-
perature (SM)
- 9 .. 99 °C 1
In 0.3 Exhaust temperature
(SF)
- 9 .. 99 °C 1
In 0.4
Domestic hot water
sensor temperature
(SS)
- 9 .. 99 °C 1
In 0.5 AUX auxiliary sensor - 9 .. 99 °C 1
In 0.6 Actual heating SET
temperature
Par. 13
… Par.
14
°C 1
In 0.7 Power level 0 .. 99 % 1
In 0.8 DHW Flow rate 0 .. 99 l/min 0.1
In 0.9
Water pressure trans-
ducer reading (when
fitted)
0 .. 99 bar 0.1
In 1.0 Actual speed fan
number
0 .. 99
RPM x
100
1
TABLE OF COUNTER DISPLAYED
Type No. Description Range U/M Step
CO 0.0 total no. of boiler
operating hours
0 .. 99 h x 1000
0.1; from
0.0 to 9.9;
1; from 10
to 99
CO 0.1 total no. of burner
operating hours
0 .. 99 h x 1000
0.1; from
0.0 to 9.9;
1; from 10
to 99
CO 0.2 total no. of burner
ignitions
0 .. 99 h x 1000
0.1; from
0.0 to 9.9;
1; from 10
to 99
CO 0.3 total no. faults 0 .. 99 x 1 1
CO 0.4
total no. of times
installer parameters
"tS"accessed
0 .. 99 x 1 1
CO 0.5
total no. of times
OEM parameters
accessed
0 .. 99 x 1 1
CO 0.6 Countdown to the
next service
1 ..
199
months 1
TABLE OF ACTIVATED ALARMS/FAULTS
Type No. Description
AL 00 Last activated alarm/fault
AL 01 Last but one activated alarm/fault
AL 02 Third from last activated alarm/fault
AL 03 Previous activated alarm/fault
AL 04 Previous activated alarm/fault
AL 05 Previous activated alarm/fault
AL 06 Previous activated alarm/fault
AL 07 Previous activated alarm/fault
AL 08 Previous activated alarm/fault
AL 09 Previous activated alarm/fault
7.6 Checks
7.6.1 Chimney sweep function
The chimney sweeper function is used by the qualified mainte-
nance technician to check the mains gas pressure, detect the
combustion parameters and to measure the combustion effi-
ciency. A combustion analysis should not be conducted until a
satisfactory inlet working pressure test has been completed.
This function lasts 15 minutes and is activated by proceeding
as follows:
– if the panel (2) has not already been removed, remove the
two screws (1), pull the front panel (2) forwards and release
it from the top by lifting it
2
1
Fig. 41