manualshive.com logo in svg

Silicon Laboratories EMBER EM358 series, Справочное руководство, Страница: 173 / 257

Поделиться
Скачать
Silicon Laboratories EMBER EM358 series Скачать руководство пользователя страница 173

EM358x 

 

 

Rev. 0.4 

173 

 

 

Figure 10-11. Counter Timing Diagram, Update Event with TIM_ARBE = 1 (counter overflow) 

 

10.3.3  Clock Selection 

The counter clock can be provided by the following clock sources: 

 

Internal clock (PCLK) 

 

External clock mode 1: external input pin (TIy) 

 

External clock mode 2: external trigger input (ETR) 

 

Internal trigger input (ITR0): using the other timer as prescaler. Refer to the section Using One Timer as 

Prescaler for the Other Timer for more details. 

10.3.3.1  Internal Clock Source (CK_INT) 

The internal clock is selected when the slave mode controller is disabled (TIM_SMS = 000 in the TIMx_SMCR 

register). In this mode, the TIM_CEN, TIM_DIR (in the TIMx_CR1 register), and TIM_UG bits (in the TIMx_EGR 

register) are actual control bits and can be changed only by software, except for TIM_UG, which remains cleared 

automatically. As soon as the TIM_CEN bit is written to 1, the prescaler is clocked by the internal clock CK_INT. 
Figure 10-12 shows the behavior of the control circuit and the up-counter in normal mode, without prescaling. 

 

Figure 10-12. Control Circuit in Normal Mode, Internal Clock Divided by 1 

Содержание EMBER EM358 series


































































































































































































































































Отзывы:

Нет отзывов