Silicon Graphics TP900 Скачать руководство пользователя | Manualshive

Страница: 43 / 72

background image

Powering Off the Enclosure

007-4428-003

27

1.

Apply AC power to the enclosure. Turn the power supply module(s) switch to the
ON position. The green Power Output LED should be lit and the red Fault LED
should be off.

Note:

In a dual-PSU system, it does not matter which PSU is powered on first.

2. All LEDs on the ESI/Ops Panel should be lit green, and the disk drive motors

should start when the enclosure power is activated.

Note:

All LEDs on the ESI/Ops panel should be lit green when power is applied,

which indicates that the system is functioning correctly. If any show amber, then a
problem exists. See Chapter 4 for troubleshooting information.

All drives in the enclosure should automatically start their motors after power is applied.
If this has not occurred, there may be a power problem (a power fault indication would
normally be active).

Powering Off the Enclosure

To power off the enclosure, switch off the power supply modules installed in the
enclosure.

«
...
41
42
43
44
45
...
»

Содержание TP900









































































Отзывы:

Нет отзывов

Похожие инструкции для TP900

XCubeSAN XS5224D

Бренд: Qsan Technology Страницы: 143

4big Spare Drive

Бренд: LaCie Страницы: 24

Бренд: V-TAC Страницы: 28

Бренд: LaCie Страницы: 48

Бренд: Sako Страницы: 19

Бренд: NetApp Страницы: 9

Бренд: IBM Страницы: 11

Бренд: Segger Страницы: 56

Expansion STEB6000403

Бренд: Seagate Страницы: 5

Бренд: Panasonic Страницы: 33

Бренд: Panasonic Страницы: 48

StorageScaler 2460

Бренд: DataDirect Networks Страницы: 46

Бренд: DataDirect Networks Страницы: 106

Бренд: Mitsubishi Electric Страницы: 2

Бренд: Mitsubishi Electric Страницы: 23

Бренд: Mitsubishi Electric Страницы: 23

Бренд: Ferm Страницы: 4

Бренд: Clarke Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды