Silicon Graphics TP900 Скачать руководство пользователя | Manualshive

Страница: 37 / 72

background image

Attaching Interface Cables

007-4428-003

21

Attaching Interface Cables

This section explains which of the connectors on the I/O modules should be used to
connect external Ultra-3 SCSI-compatible cables.

As seen from the rear of an I/O module, the connector on the right-hand side connects
to channel 1 (device bays 1/1, 2/1, 1/2, 2/2). The connector on the left-hand side
connects to channel 2 (device bays 1/3, 2/3, 1/4, 2/4). This applies to I/O modules
installed in either location (1/1 or 1/3).

Table 2-1 shows the cables that are supported

1 x 8 Configuration

Connect the interface cable to the channel 1 connector and attach a terminator to the other
I/O connector, as shown in Figure 2-1.

Caution:

External termination must be fitted to the unused I/O connector to ensure

termination of the SCSI bus. I/O modules do not contain any bus termination.

Table 2-1

Supported cables

Cable Combination

SGi Part Number

Cables for U160/U320 Max .(1m) 013-1043-001

Cables for U160/U320 Max .(2m) 018-1046-001

«
...
35
36
37
38
39
...
»

Содержание TP900









































































Отзывы:

Нет отзывов

Похожие инструкции для TP900

Бренд: ABSCO SHEDS Страницы: 21

Бренд: LaCie Страницы: 22

EASY ROLL 170.S/2/PS

Бренд: garofalo Страницы: 12

Fiberglass Underground Storage Tanks

Бренд: Xerxes Страницы: 31

Бренд: Tiger Страницы: 16

Бренд: Rocstor Страницы: 132

Supporter AM 1200 FH

Бренд: Beck Страницы: 32

Бренд: DEC Страницы: 94

Бренд: Mercia Garden Products Страницы: 9

Rugged USB3 Thunderbolt™ Series

Бренд: LaCie Страницы: 29

Бренд: USP Страницы: 29

Бренд: Supatool Страницы: 2

Бренд: Targus Страницы: 24

Бренд: Teac Страницы: 4

SuperStorageSystem SSG-2028R-DN2R48L

Бренд: Supermicro Страницы: 85

Rugged RAID Pro

Бренд: LaCie Страницы: 26

Бренд: POMCube Страницы: 18

Silver River II ST0018Z

Бренд: Thermaltake Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды