Silicon Graphics TP900 Скачать руководство пользователя

Страница: 52 / 72

007-4428-003

3: Replacing Modules

Replacing I/O Modules

Follow these steps to remove an I/O module from the SGI TP900 enclosure:

Caution:

Do not remove a module unless a replacement can be immediately added. The

system must not be run without all modules in place.

Loosen the screws securing the retaining bracket (see Figure 3-4) and slide the
bracket down, until it is clear of the side of the I/O module.

Figure 3-4

I/O Module Retaining Bracket

2. Slide the I/O module out of the enclosure.

3. Slide the replacement I/O module fully into the enclosure. You will feel a slight

resistance as you insert the card in the PCI connector and as the rear face of the I/O
module becomes flush with the rear face of the PSU.

4. Return the retaining bracket to the center position and tighten the securing screws.

Retaining bracket

FAULT

OUTPUT

GOOD

FAULT

OUTPUT

GOOD

CHANNEL 2

CHANNEL 1

CHANNEL 2

CHANNEL 1

I/O module

Содержание TP900









































































Результаты поиска

Содержание TP900

Отзывы:

Похожие инструкции для TP900

Бренды по названию

Популярные бренды

Silicon Graphics TP900, Руководство пользователя

Результаты поиска

Содержание TP900

Отзывы:

Похожие инструкции для TP900

Бренды по названию

Популярные бренды