Silicon Graphics TP900 Скачать руководство пользователя | Manualshive

Страница: 40 / 72

background image

24

007-4428-003

2: Setup and Operation

Important:

In a 2 x 4 configuration, the termination for each channel is located on the

other I/O module from where the interface cable is connected. For example, the
terminator for channel 1 is located on the left I/O module (1/3), whereas the interface
cable is connected to the right I/O module (1/1). See Figure 2-2 for an illustration of the
proper cable and terminator configuration.

SCSI_ID Addressing

This section shows the SCSI_ID base address for each drive in 1 x 8 and 2 x 4
configurations. See “Storage System Bay Numbering Convention” on page 17 for the
drive module numbering convention.

1x 8 Configuration

In a 1 x 8 configuration with a loopback module installed, the single I/O module (1/1)
controls the range of all the drives. Figure 2-3 shows the SCSI_ID base address for each
drive.

Figure 2-3

1 x 8 SCSI_ID Addressing

SCSI_ID 1

SCSI_ID 3

SCSI_ID 11

SCSI_ID 9

SCSI_ID 2

SCSI_ID 4

SCSI_ID 10

SCSI_ID 12

«
...
38
39
40
41
42
...
»

Содержание TP900









































































Отзывы:

Нет отзывов

Похожие инструкции для TP900

Бренд: IBM Страницы: 2

Бренд: Unior Страницы: 2

Бренд: QNAP Страницы: 62

Бренд: QNAP Страницы: 130

Бренд: Zhejiang Longyard Trade Industrial Страницы: 18

Бренд: Seagate Страницы: 46

Бренд: Patiowell Страницы: 38

Бренд: IBM Страницы: 314

BASIC PRO SERIES

Бренд: Borroughs Страницы: 17

Бренд: U-Line Страницы: 9

Бренд: Yardmaster Страницы: 28

Бренд: Yardmaster Страницы: 24

EonStor DS B Series

Бренд: Infotrend Страницы: 157

Бренд: Dedicated Micros Страницы: 12

WD VelociRaptor WD1500BLFS

Бренд: Western Digital Страницы: 2

Бренд: Trinity Страницы: 12

Basics TLS-4820

Бренд: Trinity Страницы: 16

Бренд: Nexsan Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды