Silicon Graphics TP900 Скачать руководство пользователя

Страница: 49 / 72

Replacing Power Supply Modules

007-4428-003

Replacing Power Supply Modules

Follow these steps to replace a power supply module or a power supply blank module
on the SGI TP900 enclosure:

Warning:

Hazardous voltage and current levels are present inside the storage

subsystem. The replacement of rear-bay modules should only be performed by
technically qualified personnel.

Caution:

Do not remove a module unless a replacement can be immediately added. The

system must not be run without all modules in place.

Switch off the faulty module and disconnect the power supply cord.

Note:

If you have two power supply modules installed, one power supply module

will maintain power to the enclosure while the other module is replaced.

2. Loosen the screws securing the retaining bracket (see Figure 3-1) and slide the

bracket upwards, until it is clear of the side of the power supply module.

Figure 3-1

Power Supply Module Retaining Bracket

FAULT

OUTPUT

GOOD

CHANNEL 2

CHANNEL 1

Retaining bracket

Содержание TP900









































































Результаты поиска

Содержание TP900

Отзывы:

Похожие инструкции для TP900

Бренды по названию

Популярные бренды

Silicon Graphics TP900, Руководство пользователя

Результаты поиска

Содержание TP900

Отзывы:

Похожие инструкции для TP900

Бренды по названию

Популярные бренды