Silicon Graphics TP900 Скачать руководство пользователя | Manualshive

Страница: 28 / 72

background image

12

007-4428-003

1: Storage System Features

Input/Output (I/O) Module

Two I/O modules are mounted in the rear of the system utilizing Ultra-3 SCSI interfacing
with the host computer system. Two I/O module configurations are available, as follows:

•

The 1 x 8 configuration is used to create a SCSI bus structure with one string of 8
drives. It consists of one standard I/O module with two VHDCI connectors for
main I/O purposes and a switch to set the SCSI-ID range. The second module is a
loopback PCB with no external connectors.

•

The 2 x 4 configuration is used to create a SCSI bus structure with two strings of 4
drives. The two modules are the standard I/O modules with two VHDCI
connectors for main I/O purposes.

Figure 1-11 shows a standard Ultra-3 I/O module.

Figure 1-11

Ultra-3 SCSI I/O Module

CHANNEL 2

CHANNEL 1

«
...
26
27
28
29
30
...
»

Содержание TP900









































































Отзывы:

Нет отзывов

Похожие инструкции для TP900

Бренд: LaCie Страницы: 29

01OVLPA0806SDFW-V1

Бренд: Walton Страницы: 6

Бренд: Cutech Страницы: 2

Бренд: LaCie Страницы: 22

Бренд: LaCie Страницы: 4

Бренд: DuraMax Страницы: 81

Бренд: FDiSK Страницы: 25

MaxAttach NAS 4000

Бренд: Maxtor Страницы: 2

Supporter AM 1200 FH

Бренд: Beck Страницы: 32

Бренд: QNAP Страницы: 16

Бренд: Excel Страницы: 2

Бренд: SAJ Страницы: 42

Storage Library T24

Бренд: Tandberg Data Страницы: 6

Бренд: Magnusson Страницы: 24

Бренд: Argus Страницы: 1

Memorator Pro 5xHS

Бренд: Kvaser Страницы: 27

Бренд: Displays2go Страницы: 2

Бренд: Acomdata Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды