background image

Rack Mounting Considerations

007-6465-001

13

Server Precautions

Review the electrical and general safety precautions.

Determine the placement of each component in the rack before you install the rails.

Install the heaviest server components in the bottom of the rack first, and then work up.

Add a regulating uninterruptible power supply (UPS) to protect the server from power 
surges and voltage spikes and to keep your system operating in case of a power failure.

Allow the hot-pluggable disk drives and power supply modules to cool before touching.

Always keep the rack’s front door and all panels and components on the servers closed when 
not servicing to maintain proper cooling.

The server is not considered suitable for visual display work place devices under the German 
government ordinance for work with visual display units.

Rack Mounting Considerations

Use the guidelines provided in the following subsections to properly install the server in a rack.

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating temperature of the rack 
environment may be greater than the ambient temperature of the room. Therefore, consideration 
should be given to installing the equipment in an environment compatible with the manufacturer’s 
maximum rated ambient temperature (

35º C or 95º F)

.

Important:  

Certain system configurations using a higher-wattage processor and PCIe option 

cards may require the maximum rated ambient temperature of the operational environment be 30º 
C (86º F) or lower. Altitude of operation can also affect required ambient air temperatures, see 

Table B-1 on page 61

. Check with your SGI sales or service representative for additional 

information on this topic.

Содержание InfiniteStorage C1104-GP6













































































Отзывы: