Silicon Graphics InfiniteStorage C1104-GP6 Скачать руководство пользователя страница 65

Страница: 65 / 76

System Fans

007-6465-001

Replacing System Fans

This section describes how to remove or install a system fan.

Remove/Replace a Fan

1. If you have not already done so, remove the chassis cover to access the fans, see the example

Figure 6-6 on page 54

2. Turn off the power to the system and unplug the AC power cord.

3. Remove the failed fan's wiring connectors from the serverboard.

4. Remove and retain the four pins securing the fan assembly to the fan tray.

5. Lift the assembly housing the failed fan from the fan tray and out of the chassis, see the

example in

Figure 6-7 on page 55

6. Place the new fan into the vacant space in the fan tray, while making sure the arrows on the

top of the fan (indicating air direction) point in the same direction as the arrows on the other
fans. See

Figure 6-8 on page 56

for a fan assembly example.

7. Reconnect the fan wires to the exact same chassis fan headers as the previous fan.

8. Reconnect the AC power cord, power up the system and check that the fan is working

properly (and the control panel LED is no longer lit) before replacing the chassis cover.

Содержание InfiniteStorage C1104-GP6













































































Результаты поиска

Содержание InfiniteStorage C1104-GP6

Отзывы:

Похожие инструкции для InfiniteStorage C1104-GP6

Бренды по названию

Популярные бренды

Silicon Graphics InfiniteStorage C1104-GP6, Руководство пользователя системы

Результаты поиска

Содержание InfiniteStorage C1104-GP6

Отзывы:

Похожие инструкции для InfiniteStorage C1104-GP6

Бренды по названию

Популярные бренды